Recent content by Stout

We have kept our boats on the Columbia for a bit over 10 years. As others have said there are quite a few nice areas to go and explore but it gets repetitious after a while. We call it “Linear” boating (up river or down river). So we go up to B.C. and/or the Puget Sound every other year. One...

Start Battery You may want to investigate how many CCA’s your engine requires for a start bank. We have an 8.3L Cummins and use 2 group 32’s in parallel. We did this after removing 2 4D’s in parallel. You need to measure your box to see if they will fit and you will need to add/update the...

We bought the Fujicon TSX-1440 before our trip up to Desolation Sound this summer from PDX. They worked very well, especially while transiting the coast watching for crab pots & whales. Used them every day for 2 months, still on the same set of Duracell AA batteries. I will take them out this...

We use a ram mount for the 12” iPad Pro in our pilot house. It works well, using the larger ball size because of the weight. Would buy again.

We use e of these: https://www.wholesalemarine.com/boat-buckle-stainless-steel-kwik-lok-transom-tie-down/ to hold our 11.5’ Whaler on our deck. I found some with SS instead of plated metal. Easy on/off.

“ Have you tried the blue impellers? There supposed to be able to run dry for an extended period. They have them at Seattle Marine Supply. I haven’t tried them yet due to having numerous spares, but I can’t see how they could be worse. 60-70 hours is ridiculous-especially for a generator with...

On our Onan gen, there is a pressure switch on the discharge side of the pump. It shuts the gen down immediately when no pressure. It has saved us a couple of times when seaweed has plugged the through hull and when the impeller decides to shed its blades. We are down to a 60 hour replacement...

We carry a spare rebuilt pump and would do as Peter suggests. The macerator pump is less $$ than the vacuflush pump.

Sounds like you have been methodical on this, hopefully just the macerator duck bills. Another thought is back flushing through the deck pump out to see if water drains fast back into the tank with no restriction.

Hip, if you have looked at the duck bills in the macerator pump and they are ok, do you still have the original ABS tee? Where the NPT barbs screw in, the ABS tee will eventually develop cracks where the barb screws in, this can cause vacuum leak also. Hope this helps.

I have had good luck with Espar of Michigan, they almost always have the Espar parts I have needed. They even found a NOS Espar hydronic unit for me last fall to replace my worn out unit

Tanner MFG Tanner Mfg is another marine SS fabricator in WA. I believe they are the OEM for both Nordic Tug & American Tug. We have had them fab some items and have been very satisfied with their products. https://www.tannermfg.com/contact Tanner Manufacturing & Design, Inc. P.O. Box...

Saw this strap shown on the SENTOA forum: https://static1.squarespace.com/static/5d230a26babc7000011f71c7/t/5e4ca91c88b5487eccd115c4/1582082343289/MPS_Product_Guide_Shaft_Strap+indd.pdf Another option anyway.

I have one of the small units, clamp it near me while working on boat in hot weather. It does not move a lot of air, but enough to be useful and easy to aim. Have 2 of the mid size units, we use them around the boat as general fans as we do not have AC. Like that the mid size unit can run off...

Ken, that is normally done on a horizontal wheel blast machine with steel shot or steel grit depending on the paint spec and then into a paint booth that applies a weldable primer, it is used at most large shipbuilding companies. There are also blast and paint shops regionally that will...