Wxx3
Dauntless Award
- Joined
- Jan 10, 2013
- Messages
- 2,820
- Location
- USA
- Vessel Name
- Dauntless
- Vessel Make
- Kadey Krogen 42 - 148
Yesterday.
We got up at the crack of dawn so to be able to start engine at 06:15. The last line was thrown off at 06:45 and our Summer Adventure officially began.
Today, Sunday, 24 May, 2015, I awoke to the visage of Claudia III out the salon window, quite a change from Waterford. But how did we get here?
Casting off yesterday morning, with our bow pointed into the flooding tide, Dauntless left Waterford with hardly a ripple. A little left rudder, forward gear at idle, she glided smoothly into the oncoming 2 knot current.
I can’t begin to tell you the feelings of getting underway, cleaving the bonds that tied us to a particular place. The steady purr of the engine, the big wheel turning a big rudder, Dauntless becomes frisky. Krogens are made to roam the seas and can bring their lucky owners to virtually any place they dare to go.
We had arranged to go to the New Ross Boatyard for haul out. 12 months and 4,000 miles after our last haul out, I figured it was time again. The Waterford boatyard’s lift was too narrow for our Krogen, but they recommended the New Ross Boatyard. Our departure from Waterford was predicated on two factors: the need to depart into the current and the necessity to arrive at New Ross close to high water. That meant an hour downstream against the current and then an hour upstream with the current. Turned out there was also a swing bridge to traverse, but we had three feet to spare.
Arriving at the boat yard, with a two knot current still running, made for an exciting entrance, finally on the third attempt, Dauntless was safely cradled in the lift.
The bottom was in much better shape than I had anticipated. The previous haul out, half the anti-fouling paint was gone. This time, there were just small areas where the old ablative paint was showing through. So we, actually Karla and Larry, spent the rest of the afternoon touching up our bottom. Now it looks a bit like a moth eaten leopard, but only the fish will know.
The two zincs were half gone. I replaced the one on the rudder. The one of the shaft is a combination steel cutter attached to a clamp on zinc anode. It costs only $60. It’s the second one I’ve put on and it works wonderfully. Half eaten, it tells me it’s doing its job and no pieces of line wrapped around the shaft as had happened in the past.
We’re ready to go back in the water, but today is Sunday, so we will have a day of rest and just small jobs. I must service and grease the Ideal Windlass and probably replace one of the solar panel controllers.
The Delorme InReach is now on, and my intention is to keep it on until Dauntless returns its 2015-6 winter home October 1st. Therefore, you can find us at, https://share.delorme.com/dauntless
If there is not a current update, either the boat has sunk or I neglected to charge the InReach.
Thanks for coming along with us.
Boat Propeller Shaft Line Cutters at Zincwarehouse.com
Sorry, the pics are too hard for me to upload here, they are on my blog.
We got up at the crack of dawn so to be able to start engine at 06:15. The last line was thrown off at 06:45 and our Summer Adventure officially began.
Today, Sunday, 24 May, 2015, I awoke to the visage of Claudia III out the salon window, quite a change from Waterford. But how did we get here?
Casting off yesterday morning, with our bow pointed into the flooding tide, Dauntless left Waterford with hardly a ripple. A little left rudder, forward gear at idle, she glided smoothly into the oncoming 2 knot current.
I can’t begin to tell you the feelings of getting underway, cleaving the bonds that tied us to a particular place. The steady purr of the engine, the big wheel turning a big rudder, Dauntless becomes frisky. Krogens are made to roam the seas and can bring their lucky owners to virtually any place they dare to go.
We had arranged to go to the New Ross Boatyard for haul out. 12 months and 4,000 miles after our last haul out, I figured it was time again. The Waterford boatyard’s lift was too narrow for our Krogen, but they recommended the New Ross Boatyard. Our departure from Waterford was predicated on two factors: the need to depart into the current and the necessity to arrive at New Ross close to high water. That meant an hour downstream against the current and then an hour upstream with the current. Turned out there was also a swing bridge to traverse, but we had three feet to spare.
Arriving at the boat yard, with a two knot current still running, made for an exciting entrance, finally on the third attempt, Dauntless was safely cradled in the lift.
The bottom was in much better shape than I had anticipated. The previous haul out, half the anti-fouling paint was gone. This time, there were just small areas where the old ablative paint was showing through. So we, actually Karla and Larry, spent the rest of the afternoon touching up our bottom. Now it looks a bit like a moth eaten leopard, but only the fish will know.
The two zincs were half gone. I replaced the one on the rudder. The one of the shaft is a combination steel cutter attached to a clamp on zinc anode. It costs only $60. It’s the second one I’ve put on and it works wonderfully. Half eaten, it tells me it’s doing its job and no pieces of line wrapped around the shaft as had happened in the past.
We’re ready to go back in the water, but today is Sunday, so we will have a day of rest and just small jobs. I must service and grease the Ideal Windlass and probably replace one of the solar panel controllers.
The Delorme InReach is now on, and my intention is to keep it on until Dauntless returns its 2015-6 winter home October 1st. Therefore, you can find us at, https://share.delorme.com/dauntless
If there is not a current update, either the boat has sunk or I neglected to charge the InReach.
Thanks for coming along with us.
Boat Propeller Shaft Line Cutters at Zincwarehouse.com
Sorry, the pics are too hard for me to upload here, they are on my blog.