dock water hose connection

The friendliest place on the web for anyone who enjoys boating.
If you have answers, please help by responding to the unanswered posts.

Gordon B

Veteran Member
Joined
Jan 10, 2015
Messages
97
Location
USA
Vessel Name
Moonstruck
Vessel Make
41' Defever
Hi to all,
We have a place to connect a water hose to the boat to utilize the water at the dock. We have the right hose that we use to fill our tanks but would like to connect so we have continuous water while we are at the dock.
Is there any caveat that we should be aware of?
Should the water pump be shut off because of the city water pressure?
etc. etc.

Thanks
Gordo
 
The water pump does not need to be off, it will see the pressure from the hose and not turn on. Be careful with connecting to shore water. If you have a hose come off inside the boat, it will flow a lot of water into the bilge. Can your bilge pumps keep up? I would never leave the boat unattended with shore water hooked up. We have an RV that we always hooked up to shore water. A hose came off and the water ran until we returned to the RV. The good news is that you can’t sink an RV, it just ran out onto the ground. We have a shore water connection on our boat, but we just fill the tanks and use the pump to supply water. It helps to keep the water in the tanks fresh as it gets used regularly.
 
There are two types of shore water connections--those that keep the tank topped off and those that are connected to the plumbing AFTER the water pump. Most shore water pressure is too high for marine (and also RV) fresh water plumbing...it can blow a connection off. So you'll need a pressure reducer valve. Get some knowledgeable advice about where and how to install it before just plugging the water hose into the boat. Just be aware that there are only two kinds of pressure reducer valves--those that have failed and those that will. So NEVER leave the water on when away from the boat, even for an hour or two and never go to bed with it on. A sailboat owner I knew just went for a Sunday morning run with his dog...came back to a foot of water in his cabin. Another hour would have sunk his boat in its slip. And I've known more than one person who had to get up in the middle of the night and stepped out of his v-berth into calf deep water.

To repeat: get some knowledgeable advice before connecting it!
 
Either make it idiot proof to turn off at the dock, or but a gallon limiter/ regulator (lawn sprinkler type) and out it in line.

You can dial in 200 gallons say...that will last for days but not sink your boat if something onboard goes wrong.

There are a lot of "never dos" expressed by some.... as there are the rare occasions of catastrophes...but mamy of us have run city water for decades even as liveaboards with isdues but never catastrophes.

I turn the pump off as sometimes city water isnt as high as my pump setting....plus really no need for it to be on unless the pressure drops so low you want your onboard system to pony up pressure.
 
Last edited:
The water pump does not need to be off, it will see the pressure from the hose and not turn on. Be careful with connecting to shore water. If you have a hose come off inside the boat, it will flow a lot of water into the bilge. Can your bilge pumps keep up? I would never leave the boat unattended with shore water hooked up. We have an RV that we always hooked up to shore water. A hose came off and the water ran until we returned to the RV. The good news is that you can’t sink an RV, it just ran out onto the ground. We have a shore water connection on our boat, but we just fill the tanks and use the pump to supply water. It helps to keep the water in the tanks fresh as it gets used regularly.

+1 This occured to me. A fitting popped out and water started to flow in the ER. Fortunately we were aboard and my wife heard the sound of the flowing water so no damage.
Lesson learned: never keep the city water opened when you are away and even more, disconnect the hose so you do not risk your boat if a folk open the valve on the dock.
In fact I even found out that we almost never connect to the dock and almost always use water from the tank so it cycles more and is always fresh.

L
 
Either make it idiot proof to turn off at the dock, or but a gallon limiter/ regulator (lawn sprinkler type) and out it in line.

You can dial in 200 gallons say...that will last for days but not sink your boat if something onboard goes wrong.

That limiter is a great idea!
 
like most ideas on this forum, I wasnt the originator....but hapoy to pass it along.

be aware though, they seem to be plastic and very intolerant of any freezing weather.....

but after awhile, if you have a hose out in freezing weather with water in it and you plan on moving the next day...its like trying to coil rebar.

so freezing weather gets a pass and I just use tanks ....and if I need the hose, I store it in the shower overnight.
 
While I don't ever hook to city water for the previously mentioned reason, if you choose to, you can incorporate a flow restricter before the connection to the boat. Simply, it reduces the hose diameter from 1/2" or greater down to a much smaller size. There's nothing to fail as it's only a hole through a pipe fitting. The same thing can be accomplished by plumbing a gate valve after the dock hose. Once you have it adjusted to the minimum required flow, just remove the hand wheel. The idea is to limit the flow to about 3 gallons per minute.

Ted
 
Hi to all,
We have a place to connect a water hose to the boat to utilize the water at the dock. We have the right hose that we use to fill our tanks but would like to connect so we have continuous water while we are at the dock.
Is there any caveat that we should be aware of?
Should the water pump be shut off because of the city water pressure?
etc. etc.

Thanks
Gordo
I have seen 3 boats sunk using city water
 
While I don't ever hook to city water for the previously mentioned reason, if you choose to, you can incorporate a flow restricter before the connection to the boat. Simply, it reduces the hose diameter from 1/2" or greater down to a much smaller size. There's nothing to fail as it's only a hole through a pipe fitting. The same thing can be accomplished by plumbing a gate valve after the dock hose. Once you have it adjusted to the minimum required flow, just remove the hand wheel. The idea is to limit the flow to about 3 gallons per minute.

Ted

Yes but.......! Many older boats and maybe newer ones have plumbing that will not accept high pressure. A flow restrictor can reduce pressure while there is flow but when flow stops, the pressure will soar to that of the supply.
 
You need to understand how YOUR boat is actually plumbed. A lot of advice was forwarded here based on how OTHER people's boats are plumbed. On my old Hatteras, there were OEM pressure reducers on the shorewater feed (adjustable) plumbed in line already. There was a check valve on the pump branch that prevented back feeding the pump (and the pressure switch as well). The tank was fed by a completely different intake and the tank outlet also had a check valve to prevent water from the pump side to back feed into it.. so that was MY boat's plumbing.
 
I don't like hooking city water directly to the boat. If you are very good about truning it off every time you leave the boat, great. I find it way to easy to forget something like that. I find it much easier to hook the water hose to a 12v sprinkler valve and then to the tank fill hose. You can either use a timer to run the valve or if you have a Gobius tank monitor or a Tank Watch then you can use those to auto fill the tank. I also reduce the garden hose down to 1/4" so that if all else fails the water is coming in slower than my bildge pump can pump. The sprinkler valve should also be mounted outside the boat for safty.
 
While I don't ever hook to city water for the previously mentioned reason, if you choose to, you can incorporate a flow restricter before the connection to the boat. Simply, it reduces the hose diameter from 1/2" or greater down to a much smaller size. There's nothing to fail as it's only a hole through a pipe fitting. The same thing can be accomplished by plumbing a gate valve after the dock hose. Once you have it adjusted to the minimum required flow, just remove the hand wheel. The idea is to limit the flow to about 3 gallons per minute.

Ted

Yes, you can throttle the flow, but a gate valve is the wrong valve for that. Use a ball valve, or simply fit an orifice in line. The better and more reliable method is to use a pressure reducing valve in line. It will maintain the pressure to whatever it's set to, regardless of volume, and it won't (well, shouldn't) bleed pressure when there's no flow. Even with a PRV, there's still a potential for failure, so the advice from others to NEVER leave a connection charged that can put a virtually unlimited amount of water into the boat is spot on. Stuff breaks, and always in a sequence that Murphy rides herd on. That's why I opt not to make a connection to dockside water other than a hose into the tank.
 
Yes, you can throttle the flow, but a gate valve is the wrong valve for that. Use a ball valve, or simply fit an orifice in line. The better and more reliable method is to use a pressure reducing valve in line. It will maintain the pressure to whatever it's set to, regardless of volume, and it won't (well, shouldn't) bleed pressure when there's no flow. Even with a PRV, there's still a potential for failure, so the advice from others to NEVER leave a connection charged that can put a virtually unlimited amount of water into the boat is spot on. Stuff breaks, and always in a sequence that Murphy rides herd on. That's why I opt not to make a connection to dockside water other than a hose into the tank.

As I mentioned at the beginning of my post the preferred method was a flow restricter (orifice), no moving parts. This has nothing to do with pressure, only put a maximum limit on flow rate in case of a plumbing failure. A ball valve would be a poor choice here as it's to course an adjustment. Ideally a needle valve would be the best choice for controlling flow.

And as mentioned in my first post, I would never hook city water to my boat.

Ted
 
Yes but.......! Many older boats and maybe newer ones have plumbing that will not accept high pressure. A flow restrictor can reduce pressure while there is flow but when flow stops, the pressure will soar to that of the supply.
Thought I made it pretty clear in the first sentence that I don't hook to city water for the already mentioned reason (elevated water pressure). My post was about absolute flow restriction.

Ted
 
Thought I made it pretty clear in the first sentence that I don't hook to city water for the already mentioned reason (elevated water pressure). My post was about absolute flow restriction.

Ted

YES, and many who read your post may not have an understanding of why failures occur in a boat’s interior plumbing system. Most are related to excessive pressure and if your suggestion is followed by someone whose boat lacks a pressure reducer it can be an invitation to trouble. I find it to be poor advise to offer flow restricting suggestions to others while you yourself refrain from directly connecting to city water.

Foggysail
 
Last edited:
why is it bad advice?

if you going to do something with risk, minimizing the effect isnt bad advice...

I use city water all the time, have never seen or heard of a boat sinking from it after 12 years living aboard, 14 in the salvage business and 23 in the USCG.

Seems like many risks on a boat....., know your systems, maintain them, minimize any risks and get over the constant worring proliferated on TF.
 
Sure, I maybe was overly cautious in my response to Diver but the reason for my caution was in not knowing if ALL boats have pressure reducers at their fresh water connections. For boats with reducers there is nothing wrong with Diver’s post although I do believe that he should have made reference to one.

I use dock water most of the time. I went through 3 pressure reducers from West Marine, all failed. I designed and installed my own including reverse flow protection. I trust nothing to chance and when we are away the water is shut off.
 
Last edited:
While I don't ever hook to city water for the previously mentioned reason, if you choose to, you can incorporate a flow restricter before the connection to the boat. Simply, it reduces the hose diameter from 1/2" or greater down to a much smaller size. There's nothing to fail as it's only a hole through a pipe fitting. The same thing can be accomplished by plumbing a gate valve after the dock hose. Once you have it adjusted to the minimum required flow, just remove the hand wheel. The idea is to limit the flow to about 3 gallons per minute.

Ted

YES, and many who read your post may not have an understanding of why failures occur in a boat’s interior plumbing system. Most are related to excessive pressure and if your suggestion is followed by someone whose boat lacks a pressure reducer it can be an invitation to trouble. I find it to be poor advise to offer flow restricting suggestions to others while you yourself refrain from directly connecting to city water.

Foggysail

What part of the last sentence in my post do you not understand?

Simply, when your boat plumbing fails, this limits the flooding to 3 gallons per minute. Not sure how you see that post as in anyway endorsing the use of city water pressure. This was in response to post #4, offering another alternative to lowering your risk should the boat plumbing fail.

Ted
 
For about $10. most hardware stores have an inline device , made for washing machines that will stop the flow once past a certain point.

This is in case a hose blows with the owner absent.
 
It's difficult to sink a house but not difficult to sink a boat.

The foolproof way of not sinking a boat from city water is to not hook the boat to city water. Fill the tanks and use water from the tanks. Anything else is taking a risk. Your risk tolerance is up to you but remember, even if you have never seen a boat sink from being connected to the city water system, it can and has happened.

What worries me about these shutoff devices is, they are often made of plastic and not built to the reliability that I would want to protect my boat. I would feel better about one made to commercial or industrial standards.

I use the water from my tanks and it's never been a problem. And as someone pointed out, it keeps the tanks fresh.
 
If you're going to hook up dockside water, here's a pressure regulator with no moving parts to fail...and it's inexpensive. I don't do it often, but when I do, I use this.

https://www.walmart.com/ip/Camco-Br...75035&wl11=online&wl12=14504323&wl13=&veh=sem

1499fcb7-e326-4647-8b29-96ba418b41c0_1.fdcece07971b46b05d085ba5b0741a6e.jpeg
 
What part of the last sentence in my post do you not understand?

Simply, when your boat plumbing fails, this limits the flooding to 3 gallons per minute. Not sure how you see that post as in anyway endorsing the use of city water pressure. This was in response to post #4, offering another alternative to lowering your risk should the boat plumbing fail.

Ted

Yeah, so you limit the flow and hope your bilge pumps function as advertised. I stand by by earlier comments. If your going to use dock water, make sure you have a pressure reducer where water enters the boat. Can you understand that? :banghead:
 
Hey Gordon, good, yet a simple question. Good advice from those above, such as turning the water off when leaving the boat and carring a pressure regulator. I also have a coal activated filter from the shore hose to the pressure regulator. Below is a link of the regulator I use. Got it from Camping World. It is adjustable.


Word of additional advice. NO NOT use a shore water hose that is on the dock. Use your hose! You have no way of learning where that hose has been. I saw tour boats in Juneau use the hose down in the head to unclog it.....yep, will not be using that hose.


Adjustable Water Regulator - Lead Free - Valterra A01-1117VP - Faucets & Inlets - Camping World
 
Last edited:
When I hear of a problem on a “friend’s boat” or a “guy I knew’s ” boat, I get suspicious. I much more trust firsthand experience. I have spent my life and my career building and working on boats. Ran boatyards and marinas for over 20 years. I have seen several boats sink on moorings or in their slips. I never yet saw a boat sink from a fresh water hose failure. I never saw a boat in the water sink if all the seacocks were closed either. (I have seen several boats sink on land). We have lived on this boat 9 years. We spent 5 winters in the ice and snow of Maryland and VA. We now cruise full time. We now winter in FL. Anytime we stop at a marina we are usually there to fill our water tank, so we hook up to the dock water. When we stop at a marina somewhere for a while, we connect to city water every time and only turn it off if we are going to be away from the boat overnight.
But just to check, I have taken the dock hose and run it directly into the bilge at full volume. The bilge pump is a rule 1500. It must raise the water 5 feet and run through 11 feet of hose to go overboard. The pump system is more than capable of managing that flow. (And yes there is a backup 2000 gph secondary pump higher up.) I next turned on the water system and open a hose in the engine room to pump all the tank water into the bilge too and the 1500 could keep up with the flow from both sources. This makes me wonder how a boat can fill with water almost to the point of sinking, in only an hour? Must be a high-volume hose and the bilge pump must not be working. Not saying it didn’t happen but it would require a water flow 15,000 GPH or 25 gallons per minute over and above the bilge pump capacity to half sink a 12,000 pound, 34’ boat, one foot deeper into the water in an hour. And I do not know many dock hoses that can deliver that volume.
Just like singe vs twin, propane vs electric and what is the best anchor, we will not solve this issue to everyone’s satisfaction. Having tested our bilge pumps we have arrived at a solution which works for us. Permanent connection only turned off when we are away overnight.

Does anyone have a source for a flow based shut off with can turn off after x gallons? I have only been able to find timers which turn the water of after x minutes.
 
To echo Alaska Sea-Duction. Do not ever fill your tank from the spigot at the pump out station. You know where that hose has been!
 
If you are going to be connected to the shore water, as others have said, be sure to have a pressure regulator. The Jabsco hull inlets do have this feature built in.

Marine Water Pressure Regulators
https://www.defender.com/category.jsp?id=2234266
Jabsco Water Pressure Regulator Item # : 502603; Type: In-Line, Color: White; Limits Inlet Water Pressure to 45 PSI; Inlet: GHT Fitting, Outlet: 1/2" NPT Male; Model Number: 44411-0045, Designed for day and night protection of the entire plumbing system from unregulated city water system hook-ups. Whether connected to ..
 
If you are going to be connected to the shore water, as others have said, be sure to have a pressure regulator. The Jabsco hull inlets do have this feature built in.

Marine Water Pressure Regulators
https://www.defender.com/category.jsp?id=2234266
Jabsco Water Pressure Regulator Item # : 502603; Type: In-Line, Color: White; Limits Inlet Water Pressure to 45 PSI; Inlet: GHT Fitting, Outlet: 1/2" NPT Male; Model Number: 44411-0045, Designed for day and night protection of the entire plumbing system from unregulated city water system hook-ups. Whether connected to ..

I had one of those and changed it out for a non-regulator type. My boat has all 3/4 inch copper plumbing. 45psi just doesn't do it for me in the shower. I like 55-60psi, so I adjust the pressure for that.
 
Back
Top Bottom