Forum: Other Trawler Systems
Yesterday, 11:54 AM
|
Replies: 4
Views: 170
|
Forum: Power Systems
Yesterday, 11:51 AM
|
Replies: 11
Views: 431
|
Forum: Anchors and Anchoring
Yesterday, 11:36 AM
|
Replies: 5
Views: 243
Rust will cause trouble. A friend had...
Rust will cause trouble. A friend had snarling big time and the final fix was,
new chain. In his case the snarling would no longer unsnarl fully so was binding going out and back in.
It...
|
Forum: Anchors and Anchoring
Yesterday, 11:27 AM
|
Replies: 8
Views: 618
No one??
My boat and anchor are much smaller...
No one??
My boat and anchor are much smaller but what I see may require you to replace the roller setup with a longer and wider unit. Of course strength will have to be provided. Connections,...
|
Forum: General Discussion
Yesterday, 11:13 AM
|
Replies: 3
Views: 212
This not uncommon. No, I do not have your...
This not uncommon. No, I do not have your engines so have not run into this specifically.
What you describe is likely loose, corroded or poorly done connections. THe fact you did a bunch of...
|
Forum: General Discussion
Yesterday, 10:13 AM
|
Replies: 9
Views: 397
|
Forum: General Discussion
Yesterday, 09:49 AM
|
Replies: 30
Views: 1,800
Do the online "digging" first but I have seen...
Do the online "digging" first but I have seen this not work out so well in some cases that need a phone call. Yes, a phone call can sometimes work where online failed.
If you can get ahold of...
|
Forum: General Discussion
05-14-2022, 10:30 AM
|
Replies: 3
Views: 185
|
Forum: General Discussion
05-14-2022, 10:20 AM
|
Replies: 30
Views: 1,800
|
Forum: General Discussion
05-13-2022, 10:20 AM
|
Replies: 8
Views: 244
|
Forum: General Maintenance
05-12-2022, 10:23 PM
|
Replies: 3
Views: 146
|
Forum: Power Systems
05-12-2022, 10:17 PM
|
Replies: 11
Views: 403
I don't use anything regularily.
Turn...
I don't use anything regularily.
Turn the fuel over and a lot of problems will not show up.
Be carefull about your vendor, that they move lots of fuel and have lots of customer. Ask...
|
Forum: Electrical and Electronics & Navigation
05-11-2022, 07:08 PM
|
Replies: 13
Views: 373
Overprotection was a more common worry with...
Overprotection was a more common worry with wooden boats. A too high voltage could actually damage the wood around any metal protrusions into the seawater.
There is a range of acceptable...
|
Forum: Electrical and Electronics & Navigation
05-11-2022, 06:50 AM
|
Replies: 13
Views: 373
|
Forum: Power Systems
05-11-2022, 05:51 AM
|
Replies: 15
Views: 695
|
Forum: Electrical and Electronics & Navigation
05-10-2022, 08:31 AM
|
Replies: 16
Views: 624
|
Forum: General Discussion
05-08-2022, 11:00 AM
|
Replies: 16
Views: 753
I think TOm nailed it. Narrow channels, Fjord...
I think TOm nailed it. Narrow channels, Fjord like inlets can amplify the neighbouring winds and "channel" into much stronger and maybe concerning winds that the more open areas won't see. ...
|
Forum: General Discussion
05-08-2022, 10:52 AM
|
Replies: 3
Views: 429
|
Forum: General Discussion
05-08-2022, 10:45 AM
|
Replies: 9
Views: 388
|
Forum: Electrical and Electronics & Navigation
05-07-2022, 09:48 AM
|
Replies: 74
Views: 2,693
Excellent points.
Is this a new to you...
Excellent points.
Is this a new to you boat. If so Kolivers suggestion would be very valid.
Something I just though of is have you checked for Ghost loads. I have had a few on mine,...
|
Forum: Electrical and Electronics & Navigation
05-07-2022, 09:24 AM
|
Replies: 74
Views: 2,693
What runs overnight? What is their draw in...
What runs overnight? What is their draw in watts or V & A?
If electronics other than a dedicated anchor alarm is operating and the E.R. fans are running then you may be expecting to much.
...
|
Forum: Power Systems
05-05-2022, 11:14 AM
|
Replies: 17
Views: 875
*******I am having a similar problem. Went to...
*******I am having a similar problem. Went to start my Yanmar 4LH-HTE today and there was just a very loud spinning sound similar to a vacuum. From reading here it seems like the starter is spinning...
|
Forum: Electrical and Electronics & Navigation
05-04-2022, 06:48 PM
|
Replies: 21
Views: 604
|
Forum: General Discussion
05-04-2022, 06:39 PM
|
Replies: 50
Views: 1,669
_______Re alighnment was done after new motor...
_______Re alighnment was done after new motor mounts. same day._______
I think you missed my point. When were the new mounts installed, after splashing or while on land?
The new engine mounts...
|
Forum: General Discussion
05-04-2022, 12:27 PM
|
Replies: 50
Views: 1,669
I am assuming the shaft itself is straight. If...
I am assuming the shaft itself is straight. If not then it does not matter if all else is good.
The coupler between the shaft and the gearbox needs to be faced in a lathe so the coupler clamping...
|