Reply
 
Thread Tools Search this Thread Display Modes
 
Old 03-13-2020, 07:39 PM   #1
Veteran Member
 
Steamguy's Avatar
 
City: Seattle
Vessel Name: Inchcliffe Castle
Vessel Model: 1968 aluminium lifeboat converted to steam
Join Date: Feb 2019
Posts: 35
Running an alternator in reverse?

My predicament: I have a 25' trailer steamboat. There is no electrical system, just 2 batteries to run the lights, bilge pump, VHF, and most importantly the boiler blower, as when that stops the boat stops. My range is limited to 5 hours of operation before the batteries need a charge. (that's 2-1/2 hours out and 2-1/2 hours back to the dock). To increase my range I would like to install a small alternator.

A steam engine has no transmission, it's direct drive. When you want to reverse, the engine turns backwards for a few minutes. When you stop the boat, the engine is not turning.

My question to you is, Can I run an alternator in reverse? What happens when an alternator runs in reverse? Do I need to wire it up differently than what is considered normal?

Thanks in advance for any replies.
Ryan
__________________
Steamguy
S.S.S. Inchcliffe Castle, 25'
M/V Ruffinit, 39' Hudson DeFever
S/V Lars Vike, 25' Norse Folkboat
Steamguy is offline   Reply With Quote
Old 03-13-2020, 07:53 PM   #2
Guru
 
C lectric's Avatar
 
City: Gibsons, B.C., Canada
Vessel Name: Island Pride
Vessel Model: Palmer 32'
Join Date: Oct 2007
Posts: 4,414
The alternator itself should not care at all. It will work either rotation.

However the fan may not work well in the reverse rotation. If the blades are slanted then the fan is designed to work best one way, not the other.

There usually are universal fans whose blades do not have any slant. Those should work fine either direction. Talk to an alternator shop.
C lectric is offline   Reply With Quote
Old 03-13-2020, 08:11 PM   #3
Ted
Guru
 
Ted's Avatar
 
City: Campbell River
Vessel Name: Okisollo
Join Date: Apr 2012
Posts: 783
I doubt he'll be running in reverse long enough for the fan direction to matter, I may be wrong but.....
Ted is offline   Reply With Quote
Old 03-13-2020, 08:46 PM   #4
Guru
 
boomerang's Avatar
 
City: Kilmarnock VA
Vessel Name: Wandering Star
Vessel Model: PSN40
Join Date: Apr 2016
Posts: 1,395
I can't imagine a steam engine turning fast enough for an alternator to work.
__________________
-Shawn-
boomerang is offline   Reply With Quote
Old 03-13-2020, 08:55 PM   #5
Guru
 
boomerang's Avatar
 
City: Kilmarnock VA
Vessel Name: Wandering Star
Vessel Model: PSN40
Join Date: Apr 2016
Posts: 1,395
Maybe another avenue would be add another battery or 2 to your bank and add a couple of 100w solar panels to offset the discharge. 2 100w panels should be good for 6-8 amps of charge in good conditions. Plus it'll be easier than trying to engineer a steam powered charging system, IMO.
__________________
-Shawn-
boomerang is offline   Reply With Quote
Old 03-13-2020, 09:15 PM   #6
Guru
 
KnotYet's Avatar
 
City: Los Angeles
Join Date: Feb 2020
Posts: 1,487
Quote:
Originally Posted by boomerang View Post
I can't imagine a steam engine turning fast enough for an alternator to work.
It's all about gearing. Since the alternator addition is a 'clean sheet' design, the OP
just needs to select a driving pulley that's big enough to get the alternator into its
working rpm range.
KnotYet is offline   Reply With Quote
Old 03-13-2020, 09:27 PM   #7
Guru
 
boomerang's Avatar
 
City: Kilmarnock VA
Vessel Name: Wandering Star
Vessel Model: PSN40
Join Date: Apr 2016
Posts: 1,395
Quote:
Originally Posted by KnotYet View Post
It's all about gearing. Since the alternator addition is a 'clean sheet' design, the OP
just needs to select a driving pulley that's big enough to get the alternator into its
working rpm range.
You think that would be the best way? Idk. That would be some serious gearing. I don't charge all that great until I'm above 12-1400RPM and that's my engine RPM. The alternator turns faster than the engine!
__________________
-Shawn-
boomerang is offline   Reply With Quote
Old 03-13-2020, 10:00 PM   #8
Master and Commander
 
markpierce's Avatar
 
City: Vallejo CA
Vessel Name: Carquinez Coot
Vessel Model: penultimate Seahorse Marine Coot hull #6
Join Date: Sep 2010
Posts: 12,559
There is a thing as generators run by steam, leastwise with railroads in the past and in most current electrical plants.
__________________
Kar-KEEN-ez Koot
markpierce is offline   Reply With Quote
Old 03-13-2020, 10:02 PM   #9
Guru
 
Ka_sea_ta's Avatar
 
City: Puget Sound
Join Date: Jun 2016
Posts: 631
Why not add a couple more batteries it would be cheaper. Solar would help to.
__________________
When crap happens, turn it into fertilizer for your tree of knowledge..... Scott Brodie
Ka_sea_ta is offline   Reply With Quote
Old 03-13-2020, 11:09 PM   #10
Senior Member
 
EngNate's Avatar
 
City: Bella Bella
Vessel Name: Tenacious
Vessel Model: Uniflite 31 FB Sedan
Join Date: Feb 2019
Posts: 312
The short intervals and low rpms when reversing there will not be an issue with the alternator regardless which type of fan is used but a straight blade fan will be preferred.
__________________
Experience develops good judgement, bad judgement develops experience
EngNate is offline   Reply With Quote
Old 03-14-2020, 02:50 AM   #11
Guru
 
High Wire's Avatar
 
City: Cape May, NJ
Vessel Name: Irish Lady
Vessel Model: Monk 36
Join Date: Dec 2007
Posts: 4,964
A second battery would double his cruise time or halve his depth of discharge. Both good things. Perhaps a bank of golf cart batteries.
__________________
Archie
Irish Lady
1984 Monk 36 Hull #46
Currently in Cape May, NJ
High Wire is offline   Reply With Quote
Old 03-14-2020, 06:44 AM   #12
Guru
 
O C Diver's Avatar
 
City: Fort Myers, FL... Summers in the Great Lakes
Vessel Name: Slow Hand
Vessel Model: Cherubini Independence 45
Join Date: Dec 2010
Posts: 12,834
Yes, you can run an alternator in reverse and the straight bladed fan will work in both directions.

As previously mentioned, "how much time will you spend in reverse "? The last part is RPM. Alternators have a minimum RPM before they start producing any amount of power (and generate heat). If most of the reverse RPM will be at or just above idle speed, I wouldn't worry about changing the fan.

Regarding RPM and output, alternators and generator ends are wound to match engine RPM. There are lots of slow speed direct drive generators turning 1,800 RPM and below. What you will want to look for is an alternator for ambulance, EMS, or fire trucks. The alternators are designed for continuous high output at low RPM while working above idle at an accident scene. Leece Neville offers these units in a large frame lower RPM models in a variety of amperages. Most include an output graph (amps versus RPM).

Ted
__________________
Blog: mvslowhand.com
I'm tired of fast moves, I've got a slow groove, on my mind.....
I want to spend some time, Not come and go in a heated rush.....
"Slow Hand" by The Pointer Sisters
O C Diver is offline   Reply With Quote
Old 03-14-2020, 07:25 AM   #13
Technical Guru
 
Ski in NC's Avatar
 
City: Wilmington, NC
Vessel Name: Louisa
Vessel Model: Custom Built 38
Join Date: Jan 2014
Posts: 6,194
Agree that rotation direction and fan won't be an issue.

But alternator rpm could be an issue. On my Cummins 450C, the alternator runs about 3x engine rpm due to pulley sizes. At idle of 500rpm that has the alternator running about 1500rpm and it does not put out much. It is rated at 100 amps and at idle it might put out 15A. That used to be a problem but once I switched to all LED lights, it is tolerable. There have been times at night with fog and searchlight and fridge inverter that alt could not keep up. Ended up having to fire up the gennie.

On the steam engine, it will need a very large diameter pulley/flywheel to get the alt to work. And being direct drive, it probably does not need a flywheel, the prop takes care of that.

And some alternators need a good bit of rpm to get the exciter circuit to "wake up". Don't want one of those. I use an Autolite alt with external regulator that powers up as long as oil pressure switch is closed, you will need something similar.

Another option is a permanent magnet alternator like used on some boat gensets. Like the Onan/Kubota MDKD. Those don't make many amps, but do make over 12vdc at a pretty low rpm. Worth looking into.

And get your running lights converted to LED. That would completely solve the issue!!
Ski in NC is offline   Reply With Quote
Old 03-14-2020, 09:02 AM   #14
Guru
 
twistedtree's Avatar
 
City: Vermont
Join Date: Jan 2013
Posts: 10,092
What you are describing is a prop shaft generator. Google that and you will find a variety of solutions for sail boats looking to generate power off of a freewheeling shaft while under sail. Some are packaged products, and some are home brewed. But they have all addressed the gearing issue in one form or another.
__________________
MVTanglewood.com
twistedtree is offline   Reply With Quote
Old 03-14-2020, 10:47 AM   #15
JLD
Guru
 
City: Delaware
Join Date: Mar 2017
Posts: 681
A possible option, although a bit pricey, if you don't have the room for additional batteries, replace the existing batteries with lithium.

Jim
JLD is offline   Reply With Quote
Old 03-14-2020, 12:08 PM   #16
Veteran Member
 
City: Sidney, BC
Vessel Model: Bayliner 4387
Join Date: Apr 2012
Posts: 89
Thumbs up

Lower RPM 12 volt alternators are available.
Don't bother with automotive alternators these are typically 12,000 maximum rpm range.
Class 8 trucks, dozers, industrial diesels use large frame alternators in the 6000 maximum rpm range.
For example http://www.prestolite.com/literature...ors_FL1211.pdf
Assuming your using a tripile expansion engine turns 200 rpm
Chain or belt drive it off prop shaft at 200 rpm using 7:1 ratio and get 1400 alternator rpm @ 50 amps.
Either buy it new or go to used truck or equipment parts and look for similar used alternator.
Also look for 12 volt automotive generators from 50's to 63, they topped out about 6000 rpm. Most were about 40 amps
roddy is offline   Reply With Quote
Old 03-14-2020, 02:18 PM   #17
Guru
 
O C Diver's Avatar
 
City: Fort Myers, FL... Summers in the Great Lakes
Vessel Name: Slow Hand
Vessel Model: Cherubini Independence 45
Join Date: Dec 2010
Posts: 12,834
Leece Neville is part of Prestolite.

Ted
__________________
Blog: mvslowhand.com
I'm tired of fast moves, I've got a slow groove, on my mind.....
I want to spend some time, Not come and go in a heated rush.....
"Slow Hand" by The Pointer Sisters
O C Diver is offline   Reply With Quote
Old 03-14-2020, 02:48 PM   #18
Senior Member
 
Olebird's Avatar
 
City: Guntersville, Al
Vessel Name: StarLite
Vessel Model: Mainship 30 Pilot II - 2003
Join Date: Aug 2019
Posts: 413
https://www.dbelectrical.com/product...2305-2320.html

dbelectrical can answer all your questions - good guys!

This little alternator puts up 20A at 12 vdc - @ 6000 rpm - 35 hp tractor turning 1500 most of the time. You'll need the matching regulator - total < $150 new.

__________________
Murphy was an optimist!
All else fails, read the directions!
Web - This Little "STARLITE" of MINE!
Olebird is offline   Reply With Quote
Old 03-14-2020, 02:48 PM   #19
Veteran Member
 
Steamguy's Avatar
 
City: Seattle
Vessel Name: Inchcliffe Castle
Vessel Model: 1968 aluminium lifeboat converted to steam
Join Date: Feb 2019
Posts: 35
C Lectric, O C Diver, Ski in NC, all good suggestions and thanks! I think twistedtree nailed it -- I'd never thought of a prop shaft generator. That would be ideal! The other way to go might be the suggestion by roddy.
My original thoughts were to use a serpentine toothed belt and toothed pulleys off the prop shaft and step up the RPM that way. At hull speed my shaft turns at 333 RPM and with steam I have enormous power. But I will investigate prop shaft generators first.

As for solar, being in the PNW we are cloudy a lot of the time, and I have hardly any flat space left to mount panels. I would if I could.

Thanks all!
__________________
Steamguy
S.S.S. Inchcliffe Castle, 25'
M/V Ruffinit, 39' Hudson DeFever
S/V Lars Vike, 25' Norse Folkboat
Steamguy is offline   Reply With Quote
Old 03-14-2020, 02:57 PM   #20
Veteran Member
 
Steamguy's Avatar
 
City: Seattle
Vessel Name: Inchcliffe Castle
Vessel Model: 1968 aluminium lifeboat converted to steam
Join Date: Feb 2019
Posts: 35
Quote:
Originally Posted by Olebird View Post
https://www.dbelectrical.com/product...2305-2320.html

dbelectrical can answer all your questions - good guys!

This little alternator puts up 20A at 12 vdc - @ 6000 rpm - 35 hp tractor turning 1500 most of the time. You'll need the matching regulator - total < $150 new.


Olebird, that is a great suggestion and I'll sure look into it. My boiler blower needs 15 amps and will quit if it gets less than 11A.
I have a John Deere mower yet never even thought of that.

Thanks!
__________________
Steamguy
S.S.S. Inchcliffe Castle, 25'
M/V Ruffinit, 39' Hudson DeFever
S/V Lars Vike, 25' Norse Folkboat
Steamguy is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 04:16 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012