Reply
 
Thread Tools Search this Thread Display Modes
 
Old 09-04-2018, 06:49 PM   #1
Veteran Member
 
Marinex's Avatar
 
City: Campbell River
Vessel Model: 1967 Grand Banks 32 Sedan
Join Date: May 2014
Posts: 38
Lehman 120, Low RPM under load, OK in neutral

My friend and I both own Grand Banks boats with the Lehman 120.

On his twin engine Alaskan one engine has an issue where it can only reach about 11-1200 RPM under load when traveling but stopped in neutral the engine can be revved up to 2000 RPM easily.

He thought he had maybe picked up something in the water and wrapped it around the prop so had a diver buddy check it out but both props spin freely and nothing was on the shaft.

We changed fuel filters and bled the system to make sure the fuel was not restricted and checked transmission oil levels and oil odor for any sort of issue.

The only other clue is that he says if he keeps running it at the low RPM the engine coolant temp starts to rise, that´s why he thought something was wrapped on the prop shaft.

The Exhaust color seems normal.

Any ideas on what to try next? Could it still be a fuel issue?

thanks, Andy
Marinex is offline   Reply With Quote
Old 09-04-2018, 08:44 PM   #2
Guru
 
Nomad Willy's Avatar
 
City: Concrete Washington State
Vessel Name: Willy
Vessel Model: Willard Nomad 30'
Join Date: Oct 2007
Posts: 18,743
Get some prop diameters and pitch numbers from guys running the same engine and gear.
With that if they are all not overpropped you should know what dia and pitch you will need to load your engine correctly. It’s that simple.
__________________
Eric

North Western Washington State USA
Nomad Willy is offline   Reply With Quote
Old 09-04-2018, 09:17 PM   #3
Guru
 
City: Boston
Vessel Name: Adelante
Vessel Model: IG 30
Join Date: Nov 2016
Posts: 1,609
Start by calibrating tachometers with digital tachometer from Amazon.
Max rpm unloaded is 2400 but if you can hit 2200 you're OK.
Next check linkages to make sure movement at throttle translates to equal movement at engine . Then disconnect linkage and check top rpm again.
If valve clearance hasn't been checked in awhile it's time to do it.
If exhaust is normal color it probably isn't worn rings, valves or bore.
That leaves us with injectors or injection pump. Pull the injectors and send them out for testing and/or cleaning. Injection pump servicing is not for beginners and I don't have any great ideas on that one. I'd probably put in a new fuel pump before tearing apart the injection pump. They're inexpensive and a leaky diaphragm could cause problem.

Rising coolant temp would have me pulling the end off the heat exchanger to check for obstructions.
SoWhat is offline   Reply With Quote
Old 09-04-2018, 11:02 PM   #4
Guru
 
Nomad Willy's Avatar
 
City: Concrete Washington State
Vessel Name: Willy
Vessel Model: Willard Nomad 30'
Join Date: Oct 2007
Posts: 18,743
I thought max rpm (rated under load) was 2500 for the FL. Should rev in neutral about 2700.

But only using one engine it’s a bit like being tied to the dock/float.
__________________
Eric

North Western Washington State USA
Nomad Willy is offline   Reply With Quote
Old 09-05-2018, 06:38 AM   #5
Valued Technical Contributor
 
DavidM's Avatar
 
City: Litchfield, Ct
Join Date: Aug 2012
Posts: 6,785
Something is seriously wrong. Most diesels will rev 2-300 rpm past their wot rated hp rpm, in this case 2,700-2,800 rpm, not 2,000. Also The maximum rpm you can get under way is half of what would be expected.


Severe binding of the prop shaft or fouling of the prop and hull can cause the latter, but I would expect lots of black smoke as well. Overheating might also occur as you try to produce max hp at lower rpms. But about the only thing that would limit wot rpm in neutral is a fuel restriction or a governor setting.



So you probably have 2 or maybe 3 problems occurring simultaneously: fuel restriction being the main one or a governor set way to low, combined with a compromised cooling system.


David
DavidM is offline   Reply With Quote
Old 09-05-2018, 06:53 AM   #6
Guru
 
jleonard's Avatar
 
Join Date: Jun 2008
Posts: 5,037
You need calibrate the tachometer s first.
If not you have no idea what the engine is really doing.
You will only be guessing.
jleonard is offline   Reply With Quote
Old 09-05-2018, 09:32 AM   #7
Guru
 
City: Boston
Vessel Name: Adelante
Vessel Model: IG 30
Join Date: Nov 2016
Posts: 1,609
Quote:
Originally Posted by Nomad Willy View Post
I thought max rpm (rated under load) was 2500 for the FL. Should rev in neutral about 2700.
You're correct. Max governed speed no load - 2650, under load 2500.

The transmission oil pump is always running so I presume there is some load. I'm also guessing a 1967 lehman 120 is not going to come close to original specs leading to my guess if you're hitting 2200 you're good to go. I would run through the common issues and shoot for 2400 but I wouldn't tear apart the injection pump to do it. How many are running their 120's over 1800?
SoWhat is offline   Reply With Quote
Old 09-05-2018, 11:46 AM   #8
Guru
 
Nomad Willy's Avatar
 
City: Concrete Washington State
Vessel Name: Willy
Vessel Model: Willard Nomad 30'
Join Date: Oct 2007
Posts: 18,743
SoWhat,
You’re say’in old men can’t run fast nor should old engines?
I think if they’re in good condition they should run to specs.
__________________
Eric

North Western Washington State USA
Nomad Willy is offline   Reply With Quote
Old 09-05-2018, 01:07 PM   #9
Guru
 
City: Boston
Vessel Name: Adelante
Vessel Model: IG 30
Join Date: Nov 2016
Posts: 1,609
Quote:
Originally Posted by Nomad Willy View Post
SoWhat,
You’re say’in old men can’t run fast nor should old engines?
I think if they’re in good condition they should run to specs.
Well if my knees are any example, an old engine could be worn out...
SoWhat is offline   Reply With Quote
Old 09-06-2018, 05:54 AM   #10
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
"I think if they’re in good condition they should run to specs."

There are specs and there are specs.

An industrial rated engine decades old might take the loads ,
but the tractor engines are known for long life , no one uses them for high output.
FF is offline   Reply With Quote
Old 08-28-2020, 01:02 AM   #11
Veteran Member
 
Marinex's Avatar
 
City: Campbell River
Vessel Model: 1967 Grand Banks 32 Sedan
Join Date: May 2014
Posts: 38
Solved!

Just a follow up years later in case someone else has the issue, auto parts store had the right part number on invoice but grabbed wrong filter off the shelf, similar size but not enough flow!


Once again its the simple stuff that gets you....
Marinex is offline   Reply With Quote
Old 08-28-2020, 03:47 AM   #12
Guru
 
catalinajack's Avatar
 
City: Edgewater, MD
Vessel Name: Catalina Jack
Vessel Model: Defever 44
Join Date: Nov 2011
Posts: 3,585
If you are going to adjust the valves on a FL120, the heads must be re-torqued before doing so. American Diesel recommends adjusting the valves every 500 hours. Adjusting the valves on a FL135 does not require a re-torquing of the heads. I recently did the heads and valve lash on my 120s. To give you some idea of the effect of re-torquing the heads, after doing so there was very little valve lash on all except one valve.
Quote:
Originally Posted by SoWhat View Post
Start by calibrating tachometers with digital tachometer from Amazon.
Max rpm unloaded is 2400 but if you can hit 2200 you're OK.
Next check linkages to make sure movement at throttle translates to equal movement at engine . Then disconnect linkage and check top rpm again.
If valve clearance hasn't been checked in awhile it's time to do it.
If exhaust is normal color it probably isn't worn rings, valves or bore.
That leaves us with injectors or injection pump. Pull the injectors and send them out for testing and/or cleaning. Injection pump servicing is not for beginners and I don't have any great ideas on that one. I'd probably put in a new fuel pump before tearing apart the injection pump. They're inexpensive and a leaky diaphragm could cause problem.

Rising coolant temp would have me pulling the end off the heat exchanger to check for obstructions.
catalinajack is offline   Reply With Quote
Old 08-31-2020, 06:10 AM   #13
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
I would find an outboard fuel tank with hand pump bulb and try hooking it up to the engine at the closest point .

Low power is usually lack of fuel.
FF is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 07:41 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012