Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-05-2022, 09:26 PM   #1
Senior Member
 
Brisyboy's Avatar
 
City: Brisbane
Vessel Name: Malagari
Vessel Model: Island Gypsy 36 Europa
Join Date: Mar 2015
Posts: 422
Urgent help required

A few hours ago we left the marina heading for one of our favourite anchorages near a dog park and sheltered etc. it takes about 90mins. One the way I had a rush of blood and fired up the generator (Westerbeke ) to make sure it ran (which it did no problems)so that we could make breakfast etc when we arrived. Anchored up and went to start the generator,,,,nothing,,,,,no lights behind the instruments, no clicking from the engine room meaning a cold breakfast. YUK .. I`m heading down to the ER to hit it with a medium sized hammer but thought there might be a more cautious approach to troubleshooting. Any ideas welcome.

Thank
__________________
George
Brisbane
IG 36 Europa
Brisyboy is offline   Reply With Quote
Old 08-05-2022, 09:34 PM   #2
Guru
 
Blissboat's Avatar
 
City: Jacksonville Beach, FL
Join Date: May 2015
Posts: 1,252
Is the starter battery alive? If so, is there a battery [isolation] switch, and if so is that switch turned to the "On" position?
__________________
"Less judgment than wit is more sail than ballast. Yet it must be confessed that wit give an edge to sense, and recommends it extremely." ~ William Penn
Blissboat is offline   Reply With Quote
Old 08-05-2022, 09:50 PM   #3
Guru
 
C lectric's Avatar
 
City: Gibsons, B.C., Canada
Vessel Name: Island Pride
Vessel Model: Palmer 32'
Join Date: Oct 2007
Posts: 4,414
++++++Anchored up and went to start the generator,,,,nothing,,,,,no lights behind the instruments, no clicking from the engine room meaning a cold breakfast. ++++++

Check the voltage of the battery. If to low that is what you will get, no action or clicks.
Be sure the switch is turned on of course.
But the no clicks and no panel lights tells me it is not likely a goofy starter motor.
C lectric is offline   Reply With Quote
Old 08-05-2022, 10:05 PM   #4
Senior Member
 
Slowmo's Avatar
 
City: Lafayette, CA
Vessel Name: Esprit
Vessel Model: 40' Tollycraft tricabin diesel
Join Date: Oct 2018
Posts: 453
It sounds as if it started up fine not long before you anchored. So look for something simple like a loose battery connection, switch turned off, blown fuse, etc.
Slowmo is offline   Reply With Quote
Old 08-05-2022, 10:12 PM   #5
Senior Member
 
Brisyboy's Avatar
 
City: Brisbane
Vessel Name: Malagari
Vessel Model: Island Gypsy 36 Europa
Join Date: Mar 2015
Posts: 422
Thanks everyone who jumped in so quickly in response to my urgent request for help.............as luck would have it I gave it one last try before getting my hands dirty with your suggestions and the bloody thing fired straight up - did that a couple of times as per normal. Now I`m thinking that the "ignition switch" needs a clean or replacement.

Dinner tonight looks hopeful.......

Thanks again
__________________
George
Brisbane
IG 36 Europa
Brisyboy is offline   Reply With Quote
Old 08-06-2022, 08:00 AM   #6
Guru
 
mike66's Avatar
 
City: Warwick, RI
Vessel Name: Susan Helena
Vessel Model: Albin40
Join Date: Oct 2014
Posts: 523
I had trouble with one of the toggles getting wonky. Forgot which one, might have been the stop switch. Found it by luck wiggling things around trying to troubleshoot the same problem as yours. Found a replacement of the same type momentary STDP I think on Amazon or ebay. Westerbeke wanted around 15 plus 30 shipping (and I live 1/2 hr away from their facility) no local pickup option.
mike66 is offline   Reply With Quote
Old 08-07-2022, 05:41 AM   #7
Guru
 
Flatswing's Avatar
 
City: Windmill Harbour, Hilton Head Island, SC
Vessel Name: River Girl
Vessel Model: 2004 DeFever 49 RPH
Join Date: Sep 2016
Posts: 573
Quote:
Originally Posted by mike66 View Post
I had trouble with one of the toggles getting wonky. Forgot which one, might have been the stop switch. Found it by luck wiggling things around trying to troubleshoot the same problem as yours. Found a replacement of the same type momentary STDP I think on Amazon or ebay. Westerbeke wanted around 15 plus 30 shipping (and I live 1/2 hr away from their facility) no local pickup option.
mine turned out to be the fuse holder on the generator control box, one of the spade connectors was not properly seated leading to intermittent identical symptoms. I must have inadvertently disturbed the connector when I swapped out the voltmeter 2 yrs. ago!
__________________
Jeremy
Flatswing is offline   Reply With Quote
Old 08-07-2022, 07:21 AM   #8
Senior Member
 
TowLou's Avatar
 
City: North NJ
Vessel Name: Bassey
Vessel Model: 17' Bass
Join Date: Aug 2016
Posts: 438
Was going to chime in to say check the switch first for something so sudden. Enjoy!
TowLou is offline   Reply With Quote
Old 08-09-2022, 02:41 PM   #9
TJM
Senior Member
 
City: Essex, Ct.
Vessel Name: Harmony
Vessel Model: 1982 41' President
Join Date: May 2013
Posts: 442
I would be more specific on your subject line to get more input.
Suggest "Cant make breakfast" or "Westerbeke wont start", your choice.
__________________
Tom
"Harmony"
1982 41' President
TJM is offline   Reply With Quote
Old 08-10-2022, 09:30 PM   #10
Guru
 
C lectric's Avatar
 
City: Gibsons, B.C., Canada
Vessel Name: Island Pride
Vessel Model: Palmer 32'
Join Date: Oct 2007
Posts: 4,414
Quote:
Originally Posted by Brisyboy View Post
Thanks everyone who jumped in so quickly in response to my urgent request for help.............as luck would have it I gave it one last try before getting my hands dirty with your suggestions and the bloody thing fired straight up - did that a couple of times as per normal. Now I`m thinking that the "ignition switch" needs a clean or replacement.

Dinner tonight looks hopeful.......

Thanks again
I know I am late but that is often a symptom of poor connections of the cables to the battery posts.
DOn't ignore the ign. sw. of course but untill you have gone through ALL of the battery cable connections spend a bunch of time on that part.
Do NOT just look at them, Open them up and clean both the ID of the clamps, the battery posts and the cable terminal to battery clamp connections.

There are inexpensive tools for this job available at any decent auto parts place:
-- A battery brush to make the cleaning of both parts of the connection quick and easily done.
-- A battery clamp spreader to open the clamp a bit if it is to tight fitting.
-- A battery terminal puller so the use of screwdrivers is not needed which often lead to their own problem making.. Hammering and poor prying techniques can break the post seal.
--An d of course some wrenches for undoing the nuts.
C lectric is offline   Reply With Quote
Old 08-10-2022, 11:12 PM   #11
Senior Member
 
Slowmo's Avatar
 
City: Lafayette, CA
Vessel Name: Esprit
Vessel Model: 40' Tollycraft tricabin diesel
Join Date: Oct 2018
Posts: 453
I've had ignition switches do this especially if they sit for periods without use.
Slowmo is offline   Reply With Quote
Old 08-15-2022, 04:43 PM   #12
Senior Member
 
Island Cessna's Avatar
 
Join Date: Feb 2011
Posts: 305
Quote:
Originally Posted by Slowmo View Post
I've had ignition switches do this especially if they sit for periods without use.


Me too.
Island Cessna is offline   Reply With Quote
Old 08-15-2022, 05:59 PM   #13
Senior Member
 
TowLou's Avatar
 
City: North NJ
Vessel Name: Bassey
Vessel Model: 17' Bass
Join Date: Aug 2016
Posts: 438
Quote:
Originally Posted by Island Cessna View Post
Me too.
If the contacts are not brass and just some cheap metal certainly will happen.
TowLou is offline   Reply With Quote
Old 08-19-2022, 01:54 PM   #14
TBW
Member
 
City: Easton
Join Date: Apr 2019
Posts: 13
I have a long running generator problem.
Here are some things to check.

Battery volts while cranking.
Oil pressure sender.
Oil pressure sensor.
Timer
Relay(s)
Temperature sensor
Fuel shut off solenoid

You may not have all of these.
In my case, I have replaced all of them and still have my problem.
The engine starts fine and immediately shuts off. Put 12 volts to the fuel solenoid and it stays open and the generator keeps running. Whatever is supposed to send 12 volts to the fuel solenoid is not doing that.
I also changed the starting switch so you should check that.

These diesel engines are very simple and dependable.
You have the engine, the generator and the company that packages them up to sell to us.
All of the interlocking "gadgets" they hang on them for sensing this and that and auto shutdown and on and on are complicated.
You have an intermittent problem which is the most fun.
Good luck.
TW
TBW is offline   Reply With Quote
Old 08-21-2022, 08:58 AM   #15
Veteran Member
 
City: Plantation
Vessel Name: Fancy Nancy
Vessel Model: Meridian 411 Sedan Bridge
Join Date: Feb 2019
Posts: 35
I had a similar issue a while back, and found out the switch for the generator on the battery control panel had taken a crap. Replaced the switch and was back in business.
Captankirk is offline   Reply With Quote
Old 08-21-2022, 09:03 AM   #16
TBW
Member
 
City: Easton
Join Date: Apr 2019
Posts: 13
I have a breaker from the generator out to the main panel.
Not sure about a switch. Will look.
Thanks TW
TBW is offline   Reply With Quote
Old 08-21-2022, 12:40 PM   #17
Guru
 
kapnd's Avatar
 
City: hawaii
Vessel Name: #31
Vessel Model: ex-Navy MUB 50 fish/cruise
Join Date: Aug 2013
Posts: 873
Get a bigger hammer!
__________________
You can lead a horse to water,
But you can't make him ski...
kapnd is offline   Reply With Quote
Old 08-21-2022, 01:03 PM   #18
Senior Member
 
2savage's Avatar
 
City: Valley Cottage NY
Vessel Name: Savage
Vessel Model: Seaton 50 expedition trawler
Join Date: Feb 2017
Posts: 278
The Westerbeke has a 'reset' button close to the control panel. Remember that you need to give the glow plugs a good ten seconds plus there is also need to use the glow plug switch for the fuel pump to build pressure..
__________________
I spent most of my money on boats, booze and women. The rest I just wasted.
2savage is offline   Reply With Quote
Old 08-21-2022, 01:06 PM   #19
Senior Member
 
2savage's Avatar
 
City: Valley Cottage NY
Vessel Name: Savage
Vessel Model: Seaton 50 expedition trawler
Join Date: Feb 2017
Posts: 278
Next plan if this does not work; there are several sensors tha need to be closed for the engine to run. One is an oil pressure switch, port side. There are two switches here and it's the lower one. You can use a piece of wire to closwe the curcuit, then try again.

If no go, do the same again with the sensor on the exhaust elbow. This is a temperature sensor which also needs to be closed.

Finally, there's this stuff they call cereal which with a little milk and sugar can actually be eaten cold.
__________________
I spent most of my money on boats, booze and women. The rest I just wasted.
2savage is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 02:59 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012