Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-27-2014, 10:05 PM   #1
Member
 
Join Date: Jun 2010
Posts: 16
Holding Tank problem

My trawler is 13 years old and has 2700 hrs on her.,

I have recently detected effluent in the aft lazerett where the holding tank is located.
The holding tank is plastic
Nylon, I presume.
It appears that the bottom has developed a slight crack although not visable
all fittings look good.
The tank was installed prior to the aft cockpit liner.
Would hate to have to cut out deck to get to tank.
Any ideas would be appreciated
My only though would be to try and seal tank to bottom of hull thereby using the hull as the bottom of the tank.
Stanley Marcus is offline   Reply With Quote
Old 08-27-2014, 10:20 PM   #2
Guru
 
Capt.Bill11's Avatar
 
City: Sarasota/Ft. Lauderdale
Join Date: Apr 2014
Posts: 5,438
If the bottom is really cracked, I don't see how you could realistically attach and seal it to the bottom of the boat. Not much likes to stick to those plastic tanks long term anyways. So sealing it to the hull would be a big issue. Plus access to all sides of the bottom of the tanks I would think.

I'm guessing there is no way to jack it up and get under it it to weld the crack?

You might be able to cut it open and use it to hold a bladder style holding tank.

Or perhaps cut an access panel in the side and try welding the crack from the inside and then sealing the access panel up.

Just brain storming here.
Capt.Bill11 is offline   Reply With Quote
Old 08-27-2014, 11:38 PM   #3
Scraping Paint
 
City: -
Join Date: Oct 2007
Posts: 13,745
My two cents is that Capt. Bill has it right. There are times when the only way to do a job effectively is to do it right the first time, and from your description it sounds like this is one of those times.

For the reasons Capt. Bill states, I think any sort of patch job will be short-lived at best. So I think that the ultimate solution will be to replace the tank. Whether the answer is a bladder tank that might make installation easier, or a new holding tank in a different place on the boat, or simply biting the bullet and taking the smartest approach to getting the failed tank out and a new tank in, I think these are the directions your mind should be focused on.
Marin is offline   Reply With Quote
Old 08-28-2014, 12:28 AM   #4
Guru
 
City: Hotel, CA
Join Date: Sep 2011
Posts: 8,323
Echo the above but to add, you wouldn't try taping a broken window pane back together and expect it to look and function well. Replacing the broken plastic tank is the only right way to fix it in my opinion.
__________________
Craig

It's easier to fool people than to convince them that they've been fooled - Mark Twain
CPseudonym is offline   Reply With Quote
Old 08-28-2014, 12:34 AM   #5
Guru
 
rochepoint's Avatar
 
City: Sidney BC Canada
Vessel Name: RochePoint
Vessel Model: 1985 Cheer Men PT38 Sedan
Join Date: Apr 2009
Posts: 1,744
Why not just empty, clean and cut up the tank in pieces where it is and put a new one where you have access room. You can have custom one built to fit any space, thats what we did.
__________________
Cheers
Mike
MV RochePoint
rochepoint is offline   Reply With Quote
Old 08-28-2014, 12:41 AM   #6
Moderator Emeritus
 
ksanders's Avatar
 
City: SEWARD ALASKA
Vessel Name: DOS PECES
Vessel Model: BAYLINER 4788
Join Date: Feb 2011
Posts: 6,266
Dont know if you boat in or around NDZ's allot but you could cut the old tank apart, then install in its place something like this



Which is a 15 gallon holding tank coupled with a waste treatment system.
__________________
Kevin Sanders
Bayliner 4788 Dos Peces
Seward, Alaska - La Paz, Baja California Sur
https://maps.findmespot.com/s/XLJZ#history/assets
ksanders is offline   Reply With Quote
Old 08-28-2014, 01:08 AM   #7
TF Site Team
 
FlyWright's Avatar
 
City: California Delta
Vessel Name: FlyWright
Vessel Model: 1977 Marshall Californian 34 LRC
Join Date: Apr 2008
Posts: 13,728
Quote:
Originally Posted by ksanders View Post
Dont know if you boat in or around NDZ's allot but you could cut the old tank apart, then install in its place something like this

Which is a 15 gallon holding tank coupled with a waste treatment system.


That would be my choice, too.
__________________
My boat is my ark. It's my mobile treehouse and my floating fishing cabin. It's my retreat and my respite. Everyday I thank God I have a boat! -Al FJB

@DeltaBridges - 25 Delta Bridges in 25 Days
FlyWright is offline   Reply With Quote
Old 08-28-2014, 08:09 AM   #8
Guru
 
rwidman's Avatar
 
City: North Charleston, SC
Join Date: Sep 2010
Posts: 4,870
I agree that attempting to patch the tank is a losing proposition. Any of the other suggestions posted are worthy of consideration.
rwidman is offline   Reply With Quote
Old 08-28-2014, 08:14 AM   #9
Guru
 
mbevins's Avatar
 
City: Windsor
Vessel Name: Keeper IV
Vessel Model: 44 Viking ACMY
Join Date: Nov 2013
Posts: 1,350
I think by far your best bet is to clean the tank. And find a new location for a replacement tank.

Sent from my Nexus 4 using Trawler
mbevins is offline   Reply With Quote
Old 08-28-2014, 08:19 AM   #10
Guru
 
Capt.Bill11's Avatar
 
City: Sarasota/Ft. Lauderdale
Join Date: Apr 2014
Posts: 5,438
What brand, year and model boat? Got any pictures?
Capt.Bill11 is offline   Reply With Quote
Old 08-28-2014, 08:44 AM   #11
Guru
 
Moonstruck's Avatar
 
City: Hailing Port: Charleston, SC
Vessel Name: Moonstruck
Vessel Model: Sabre 42 Hardtop Express
Join Date: Nov 2008
Posts: 8,276
I would not remove or do anything to the tank until all other possibilities have be eliminated. Roto molded tank seldom crack. It could be coming from another place and running down the bilge. The Purasan HoldnTreat system is what I have, and I reccomend it. However it is expensive.

Also, is it possible to access the inside of the tank through a hose connection or cut an inspection port? If so, clean it out. Then visually check it, or put clear water with a dye in it to see if that is where the leak is coming from. You could also check it with a boroscope that can be found for around $100.00.

I wouldn't want to cut up a good tank, and still have the problem.
__________________
Don on Moonstruck
Sabre 42 Hardtop Express
When cruising life is simpler, but on a grander scale (author unknown)
https://moonstruckblog.wordpress.com/
Moonstruck is offline   Reply With Quote
Old 08-28-2014, 11:51 AM   #12
Guru
 
rwidman's Avatar
 
City: North Charleston, SC
Join Date: Sep 2010
Posts: 4,870
Quote:
Originally Posted by Moonstruck View Post
............. I wouldn't want to cut up a good tank, and still have the problem.
I agree. Make sure it's the tank first.
rwidman is offline   Reply With Quote
Old 08-28-2014, 11:58 AM   #13
Member
 
Join Date: Jun 2010
Posts: 16
Thanks for all the imput. Boat is a Pacific Trawler 37
Holding Tank is 50 gallons and the stringers proclude its removal.
Hate to put a new one, in the salon. LOL
I suppose a couple of cans of radiator stop leak is not going to fix it either. LOL
Will do futher exploration but could not see any sign of hose leakage just a slight amount of aromatic brownish liquid coming from what I believe is the underside of the tank. will keep you all posted
Stanley Marcus is offline   Reply With Quote
Old 08-28-2014, 09:27 PM   #14
Guru
 
HopCar's Avatar
 
City: Miami Florida
Vessel Name: Possum
Vessel Model: Ellis 28
Join Date: Aug 2011
Posts: 5,307
If you end up going with a new tank, check Ronco Plastics. They make about 500 different tanks.
__________________
Parks Masterson
Retired from Hopkins-Carter Marine Supply
HopCar is offline   Reply With Quote
Old 08-28-2014, 10:00 PM   #15
Scraping Paint
 
City: -
Join Date: Oct 2007
Posts: 13,745
Don't forget to check the vent hose and connection to the tank if you haven't already. If the tank fills up, further flushing will force effluent out the vent hose and if there's a bad connection or hose leak, that could be the source.

Depending on how much you want to mess around trying to find the source of the effluent, you could pump the tank, then fill it with water and pump it out again, maybe a couple of times until you have reasonably clear water in the tank. Then dump in a bunch of blue dye and see what happens. If you get blue water appearing out from under the tank and you haven't operated any of the other components in the system--- toilet. etc.--- then I guess it's a pretty safe bet you have a tank leak.

Surprising, though, with a plastic tank, unless it's been vibrating against something that wore through it, or if it's a "welded up" tank and a seam has started letting go.
Marin is offline   Reply With Quote
Old 08-29-2014, 08:24 AM   #16
Guru
 
Moonstruck's Avatar
 
City: Hailing Port: Charleston, SC
Vessel Name: Moonstruck
Vessel Model: Sabre 42 Hardtop Express
Join Date: Nov 2008
Posts: 8,276
Marine sanitation systems---------Where the Affluent meet the effluent.
__________________
Don on Moonstruck
Sabre 42 Hardtop Express
When cruising life is simpler, but on a grander scale (author unknown)
https://moonstruckblog.wordpress.com/
Moonstruck is offline   Reply With Quote
Old 08-29-2014, 08:25 AM   #17
Guru
 
Capt.Bill11's Avatar
 
City: Sarasota/Ft. Lauderdale
Join Date: Apr 2014
Posts: 5,438
To much coffee?
Capt.Bill11 is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 04:41 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012