Reply
 
Thread Tools Search this Thread Display Modes
 
Old 11-13-2022, 02:49 PM   #1
Member
 
City: Cabrillo Beach
Vessel Name: Novela
Join Date: Jan 2021
Posts: 9
Mast step Californian 42 LRC

Does anyone have a photo or schematic of the mast step on a 1979 42 LRC? Does anyone have information re load the rig is rated for? Thx in advance.
boomsurf is offline   Reply With Quote
Old 11-13-2022, 07:26 PM   #2
Guru
 
Portage_Bay's Avatar
 
City: Coupeville Wa.
Vessel Name: Pelorus
Vessel Model: Californian 42 LRC
Join Date: Oct 2015
Posts: 1,853
I'll be at the boat tomorrow and can take pics. Not sure if my mast and tabernacle are original. I have the owner's manual that came with the boat. I don't recall seeing anything about the mast but I'll take a p99k.
__________________
Some things are worth doing simply because they are worth doing.
Portage_Bay is offline   Reply With Quote
Old 11-14-2022, 03:30 PM   #3
Guru
 
Portage_Bay's Avatar
 
City: Coupeville Wa.
Vessel Name: Pelorus
Vessel Model: Californian 42 LRC
Join Date: Oct 2015
Posts: 1,853
Pics of my '83 Californian 42 LRC mast.


  • Tabernacle shows the hinged mast "step". It is located on the aft cabin top immediately aft of the aft saloon windows.
  • Mast mount shows a pair of angles, one aluminum and welded to the aluminum mast. The other stainless and bolted to the aluminum angle. The bolts with wing nuts go into the receiver.
  • Receiver. Accepts the bolts with wing nuts. It is mounted on the saloon cabin top.
  • Stay attachment point. There are 3. One each port and starboard about 31" from the mast. One forward close to the fly bridge seating about 5 ft from the mast.
The Californian owner's manual has nothing to say about the mast. In my opinion it would be good for 300 lbs. Maybe 400 lbs. I have lifted about 200 lbs with mine.

If you have one or are having one built and you want to lift more than 300 lbs I advise you to get a naval engineer to calculate safe working loads. I think the vertical component of the load is pretty good because the tabernacle base is almost on top of the bulkhead separating the aft cabin from the saloon. All of that will be in compression and quite strong. The problem comes when lifting something from over the side with the boom. You will be relying upon the relatively weak stays and mast mount + receiver. Their weak point is they are surface mounted with screws to aging fiberglass covered plywood. Not through bolted with backing plates.

Though it has nothing to do with the mast and boom on a 42 LRC this little story will serve to illustrate the change in working load with boom position. A boat I used to run had a hella stout crane. With the boom vertical the safe working load was 11,000 lbs. Boom at 45 degress 2,500 lbs. Boom horizontal 1,600 lbs. Boom below horizontal 800 lbs.
Attached Thumbnails
Reciever.jpg   Mast mount.jpg   Stay attachment.jpg  
Attached Images
 
__________________
Some things are worth doing simply because they are worth doing.
Portage_Bay is offline   Reply With Quote
Reply

Tags
californian 42

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 04:02 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012