Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-13-2021, 06:01 AM   #1
Senior Member
 
City: marco island
Join Date: Apr 2012
Posts: 111
zinc problem again

Gentlemen
I appreciate all the help and info.
I can't get the zinc residue out after the zinc post breaks off the brass plug
I screw the plug back hoping the zinc will eventually
dissolve and I can put a new zinc in.
My question is will I still get protection during this period
any thoughts
jann is offline   Reply With Quote
Old 08-13-2021, 07:58 AM   #2
Valued Technical Contributor
 
DavidM's Avatar
 
City: Litchfield, Ct
Join Date: Aug 2012
Posts: 6,785
No, not much protection. The broken off zinc is covered with zinc compounds which are good insulators. Unless the zinc is in good contact with the surrounding metal of the heat exchanger it isn't doing much good.

But can you remove the end cap and get it out? What engine do you have and where is the broken off zinc? Can you screw in a replacement zinc and just let the broken off zinc slowly waste away if it isn't easy to get the end cap off?

Dvaid
DavidM is offline   Reply With Quote
Old 08-13-2021, 10:12 AM   #3
Guru
 
dhays's Avatar
 
City: Gig Harbor
Vessel Name: Kinship
Vessel Model: North Pacific 43
Join Date: May 2015
Posts: 9,046
Jann, I have the same problem. I have some plugs where the anode has broken off while trying to unscrew the anode from the plug. The amount of the anode left in the plug simply won’t have the usable surface area to provide adequate protection. So I would not do what you are asking.

I always make sure that I have a couple spare plugs around so that if I can’t put a new anode in the used plug, I have a new complete anode (plug and anode combination) or a blank plug handy to use.

I have heard that folks will use muriatic acid to dissolve the anode out of used plugs when this happens.

However…
Where do you get muriatic acid?
What type of container can you use to put the muriatic acid in to soak the plug?
How long does that take for zinc and aluminum anodes?
Does the acid harm the plugs?
__________________
Regards,

Dave
SPOT page
dhays is offline   Reply With Quote
Old 08-13-2021, 11:25 AM   #4
TF Site Team
 
Bacchus's Avatar
 
City: Seneca Lake NY
Vessel Name: Bacchus
Vessel Model: MS 34 HT Trawler
Join Date: Nov 2014
Posts: 7,826
Big box hardware stores gave muriatic acid. usually around the thinners in oaint section or cleaning solutions.
__________________
Don
2008 MS 34 HT Trawler
"Bacchus"
Bacchus is offline   Reply With Quote
Old 08-13-2021, 11:45 AM   #5
Guru
 
C lectric's Avatar
 
City: Gibsons, B.C., Canada
Vessel Name: Island Pride
Vessel Model: Palmer 32'
Join Date: Oct 2007
Posts: 4,414
A lot of this can be prevented by applying a thread sealer such as Rectorseal 5 to the anode threads. A light coating and then using pliers and wrench to SNUG the anode firmly into the cap.
Keeps seawater out of threads. so they do not degrade.
As you snug metal to metal contact will be made.
C lectric is offline   Reply With Quote
Old 08-13-2021, 06:53 PM   #6
Guru
 
dhays's Avatar
 
City: Gig Harbor
Vessel Name: Kinship
Vessel Model: North Pacific 43
Join Date: May 2015
Posts: 9,046
Quote:
Originally Posted by Bacchus View Post
Big box hardware stores gave muriatic acid. usually around the thinners in oaint section or cleaning solutions.
Thanks. I will look.
__________________
Regards,

Dave
SPOT page
dhays is offline   Reply With Quote
Old 08-13-2021, 06:56 PM   #7
Guru
 
dhays's Avatar
 
City: Gig Harbor
Vessel Name: Kinship
Vessel Model: North Pacific 43
Join Date: May 2015
Posts: 9,046
Quote:
Originally Posted by C lectric View Post
A lot of this can be prevented by applying a thread sealer such as Rectorseal 5 to the anode threads. A light coating and then using pliers and wrench to SNUG the anode firmly into the cap.

Keeps seawater out of threads. so they do not degrade.

As you snug metal to metal contact will be made.
I've been using Rectoreal 5 on the the plug threads but haven't done it on the anode threads. Again, I haven't had a problem with the anode coming out of the plug as I remove the plug, but I have had problems with not being able to remove the anode from the plug after it has been removed.
__________________
Regards,

Dave
SPOT page
dhays is offline   Reply With Quote
Old 08-14-2021, 04:44 AM   #8
Guru
 
catalinajack's Avatar
 
City: Edgewater, MD
Vessel Name: Catalina Jack
Vessel Model: Defever 44
Join Date: Nov 2011
Posts: 3,585
Quote:
Originally Posted by dhays View Post
I've been using Rectoreal 5 on the the plug threads but haven't done it on the anode threads. Again, I haven't had a problem with the anode coming out of the plug as I remove the plug, but I have had problems with not being able to remove the anode from the plug after it has been removed.
Better yet, use KoprKote, a highly conductive anti-seize compound. Anodes out-screw easily.
catalinajack is offline   Reply With Quote
Old 08-14-2021, 10:19 AM   #9
Guru
 
AlanT's Avatar
 
City: Gig Harbor, WA
Vessel Name: MoonShadow
Vessel Model: Wendon Skylounge 72'
Join Date: Oct 2012
Posts: 721
Quote:
Originally Posted by Bacchus View Post
Big box hardware stores gave muriatic acid. usually around the thinners in oaint section or cleaning solutions.
Also swimming pool supply stores sell Muriatic acid by the gallon.
~A
AlanT is offline   Reply With Quote
Old 08-14-2021, 10:21 AM   #10
Guru
 
dhays's Avatar
 
City: Gig Harbor
Vessel Name: Kinship
Vessel Model: North Pacific 43
Join Date: May 2015
Posts: 9,046
Quote:
Originally Posted by catalinajack View Post
Better yet, use KoprKote, a highly conductive anti-seize compound. Anodes out-screw easily.

I may give that a try.
__________________
Regards,

Dave
SPOT page
dhays is offline   Reply With Quote
Old 08-27-2021, 11:05 AM   #11
Senior Member
 
Newtrawlerowner's Avatar
 
City: Delray Beach, FL and Denver, CO
Vessel Name: PartnerShip II
Vessel Model: 2003 Mainship 400
Join Date: Nov 2019
Posts: 324
What I do is drill out the broken part and run a bottoming tap into the plug. Takes a few minutes. The zinc is softer than the plug so don't worry abut damaging the internal threads.
Newtrawlerowner is offline   Reply With Quote
Old 08-28-2021, 07:34 AM   #12
TF Site Team
 
Bacchus's Avatar
 
City: Seneca Lake NY
Vessel Name: Bacchus
Vessel Model: MS 34 HT Trawler
Join Date: Nov 2014
Posts: 7,826
Also try Performance Metals anodes (zinc or alum) as they have a steel wire core that reinforces the anode rod and reduces breakage.
__________________
Don
2008 MS 34 HT Trawler
"Bacchus"
Bacchus is offline   Reply With Quote
Old 08-30-2021, 06:11 AM   #13
TF Site Team
 
Bacchus's Avatar
 
City: Seneca Lake NY
Vessel Name: Bacchus
Vessel Model: MS 34 HT Trawler
Join Date: Nov 2014
Posts: 7,826
Update...
Just checked my oil cooler anode yesterday as it erodes faster than the others. Plug came out with no anode rod (broke off at plug). The good news is the steel core stayed with the anode rod and stuck out enough to grab with vise grips and wiggle / pull the spent anode out of the cooler. Without the steel core I would have been in trouble.
Another vote for Performance Metals anodes!
__________________
Don
2008 MS 34 HT Trawler
"Bacchus"
Bacchus is offline   Reply With Quote
Old 08-30-2021, 07:08 AM   #14
Senior Member
 
City: Rock Hall Md
Join Date: Nov 2019
Posts: 167
I remove zinc plugging the brass plug with household lyme away. Sometimes takes several applications but they ome brand new with no zinc crud left in the threads.
Njlarry is offline   Reply With Quote
Old 08-30-2021, 07:35 AM   #15
Guru
 
catalinajack's Avatar
 
City: Edgewater, MD
Vessel Name: Catalina Jack
Vessel Model: Defever 44
Join Date: Nov 2011
Posts: 3,585
Geez, just buy a new one or two instead of messing with acid. They are quite inexpensive. If you use KoprKote (high copper content) or other metal impregnated antiseize on the threads you will never again have the problem.
catalinajack is offline   Reply With Quote
Old 08-30-2021, 08:06 AM   #16
Senior Member
 
Newtrawlerowner's Avatar
 
City: Delray Beach, FL and Denver, CO
Vessel Name: PartnerShip II
Vessel Model: 2003 Mainship 400
Join Date: Nov 2019
Posts: 324
Performance Metals

Quote:
Originally Posted by Bacchus View Post
Update...
Just checked my oil cooler anode yesterday as it erodes faster than the others. Plug came out with no anode rod (broke off at plug). The good news is the steel core stayed with the anode rod and stuck out enough to grab with vise grips and wiggle / pull the spent anode out of the cooler. Without the steel core I would have been in trouble.
Another vote for Performance Metals anodes!

How do you buy from Performance Metals?
I tried and I needed to be a business. Is there another way?
Newtrawlerowner is offline   Reply With Quote
Old 08-30-2021, 11:37 AM   #17
TF Site Team
 
Bacchus's Avatar
 
City: Seneca Lake NY
Vessel Name: Bacchus
Vessel Model: MS 34 HT Trawler
Join Date: Nov 2014
Posts: 7,826
Quote:
Originally Posted by Newtrawlerowner View Post
How do you buy from Performance Metals?
I tried and I needed to be a business. Is there another way?
I called them and told them where I was located. They checked for a dealer in the area and said there weren't any nearby so OK to just order direct. Irs been a couple years since I bought several sets at one time. Worth a try.
__________________
Don
2008 MS 34 HT Trawler
"Bacchus"
Bacchus is offline   Reply With Quote
Old 08-30-2021, 05:41 PM   #18
Guru
 
dhays's Avatar
 
City: Gig Harbor
Vessel Name: Kinship
Vessel Model: North Pacific 43
Join Date: May 2015
Posts: 9,046
Quote:
Originally Posted by Bacchus View Post
I called them and told them where I was located. They checked for a dealer in the area and said there weren't any nearby so OK to just order direct. Irs been a couple years since I bought several sets at one time. Worth a try.


I just ordered some more a few weeks ago. I called them up and told them what I wanted. Very nice to deal with. It would be nice if they had a web store, but kind of nice to talk to a real person for a change.

Phone: 410-228-2400
When I called last they answered the phone as Caldwell Casting.
__________________
Regards,

Dave
SPOT page
dhays is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 02:37 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012