|
|
03-06-2021, 10:53 PM
|
#1
|
Senior Member
City: Manasquan NJ
Vessel Name: Mayrose
Vessel Model: Mainship 34 pilot
Join Date: Nov 2017
Posts: 150
|
Play in Stern tube bearing, what is too much
Pre-purchase a 34 Mainship Pilot, the shaft has about 1/16" play.
My 30 Mainship Pilot has no play.
What is acceptable?
Thanks
Greg
|
|
|
03-06-2021, 11:13 PM
|
#2
|
Moderator Emeritus
City: Au Gres, MI
Vessel Name: Black Dog
Vessel Model: Formula 41PC
Join Date: Jul 2015
Posts: 21,191
|
The ABYC guide for my 2” shafts says from a minimum of .005” to a maximum of .010”. It depends on what size shaft you are referring to but 1/16” is out of specs for most of our shaft sizes. The surveyor used a plastic set of feeler gauges that would bend to match the shaft OD to measure the clearance.
A 1.5” shaft goes from .004 to .009”.
A 2.5” shaft goes from .005 to .011.
Per the chart the surveyor included on my boats survey.
__________________
Boat Nut:
If you are one there is no explanation necessary.
If you aren’t one, there is no explanation possible.
|
|
|
03-06-2021, 11:21 PM
|
#3
|
Guru
City: .
Vessel Name: GOTCHA
Vessel Model: Hatteras 58 LRC
Join Date: Jun 2019
Posts: 1,103
|
There shouldn't be enough you can feel if you try to turn or shake the shafts.
__________________
Captain F. Lee - R.P.E.
USCG 200 GT Master
|
|
|
03-07-2021, 07:41 AM
|
#4
|
Senior Member
City: Manasquan NJ
Vessel Name: Mayrose
Vessel Model: Mainship 34 pilot
Join Date: Nov 2017
Posts: 150
|
It's a 2" shaft, I am going to take a dial indicator down with me and measure. Look closer at the groves.
I really appreciate the feedback.
Greg
|
|
|
03-07-2021, 07:45 AM
|
#5
|
Enigma
City: Slicker?
Join Date: Oct 2007
Posts: 16,567
|
Greetings,
Mr. B. Agree with Mr. fb. Shouldn't be able to feel any play.
__________________
RTF
|
|
|
03-07-2021, 08:12 AM
|
#6
|
Guru
City: Oconto, WI
Vessel Name: Best Alternative
Vessel Model: 36 Albin Aft Cabin
Join Date: Oct 2012
Posts: 3,145
|
There really shouldn't be any. Take a close look at the bearing, you may have to remove the prop for the best view point. If the bearing has worn even a tiny bit lopsided it's time to replace.
It is not a huge job but bear in mind that there are thousands of bearings replaced every year. It may seem impossible to get the old one out but it can be done. I had to split mine with a sawzall and get it to cave in on itself.
pete
|
|
|
03-07-2021, 06:21 PM
|
#7
|
Senior Member
City: Manasquan NJ
Vessel Name: Mayrose
Vessel Model: Mainship 34 pilot
Join Date: Nov 2017
Posts: 150
|
I measured today. ----.045" I can lift the shaft. How much will the bearing shrink when it is dry?
|
|
|
03-07-2021, 06:40 PM
|
#8
|
Moderator Emeritus
City: Au Gres, MI
Vessel Name: Black Dog
Vessel Model: Formula 41PC
Join Date: Jul 2015
Posts: 21,191
|
I don’t know that it will shrink or not but is sounds like it needs replacement.
__________________
Boat Nut:
If you are one there is no explanation necessary.
If you aren’t one, there is no explanation possible.
|
|
|
03-07-2021, 06:45 PM
|
#9
|
Enigma
City: Slicker?
Join Date: Oct 2007
Posts: 16,567
|
Greetings,
Mr. B. "How much will the bearing shrink when it is dry?" I'm guessing .000". Yep, time to replace.
__________________
RTF
|
|
|
03-07-2021, 08:00 PM
|
#10
|
Technical Guru
City: Wilmington, NC
Vessel Name: Louisa
Vessel Model: Custom Built 38
Join Date: Jan 2014
Posts: 6,194
|
0.045", yes a bit worn, but in my experience that is not putting one in panic mode. Rubber bearings tend to swell in the water. And usually the bearing is loaded either up or down in running conditions, so the play does not matter. I have been around boats with much more play that had zero symptoms as far as vibes, noise, etc. I would plan on replacing it at your convenience, maybe next scheduled haul.
|
|
|
03-07-2021, 08:21 PM
|
#11
|
Enigma
City: Slicker?
Join Date: Oct 2007
Posts: 16,567
|
Greetings,
Mr. B. Mr. Ski's answer is better (based on experience). Forget mine (based on anecdotal information).
__________________
RTF
|
|
|
03-07-2021, 08:34 PM
|
#12
|
Guru
City: Concrete Washington State
Vessel Name: Willy
Vessel Model: Willard Nomad 30'
Join Date: Oct 2007
Posts: 18,743
|
On my last haul-out the yard guy recommended I change mine. I could feel it and guessed it was under 1/16”. I’ve seen some that were over 1/8”.
When I was in the Navy I rode the ferry back and forth to North Island in SD. When he pulled up to the float and reversed to a stop there was much noise and vibration. Wouldn’t be surprised if that 40’ boat had 1/4” slop in the aft bearing.
It could be true that there’s no need for concern unless there’s so much vibration things may come apart. Most or nearly all the vibration may be an imbalanced prop, drive shaft or something bent. It would be a plus if you knew your shaft was straight and the rest balanced. I’d say if things are smooth standing in the cockpit above the prop all’s well.
__________________
Eric
North Western Washington State USA
|
|
|
03-07-2021, 09:53 PM
|
#13
|
Senior Member
City: Manasquan NJ
Vessel Name: Mayrose
Vessel Model: Mainship 34 pilot
Join Date: Nov 2017
Posts: 150
|
Thanks everyone. I am going to see if I can get the owner to replace.
Greg
|
|
|
03-07-2021, 10:26 PM
|
#14
|
Guru
City: Southport, FL near Panama City
Vessel Name: FROLIC
Vessel Model: Mainship 30 Pilot II since 2015. GB-42 1986-2015. Former Unlimited Tonnage Master
Join Date: Oct 2007
Posts: 4,984
|
Quote:
Originally Posted by Nomad Willy
On my last haul-out the yard guy recommended I change mine. I could feel it and guessed it was under 1/16”. I’ve seen some that were over 1/8”.
When I was in the Navy I rode the ferry back and forth to North Island in SD. When he pulled up to the float and reversed to a stop there was much noise and vibration. Wouldn’t be surprised if that 40’ boat had 1/4” slop in the aft bearing.
It could be true that there’s no need for concern unless there’s so much vibration things may come apart. Most or nearly all the vibration may be an imbalanced prop, drive shaft or something bent. It would be a plus if you knew your shaft was straight and the rest balanced. I’d say if things are smooth standing in the cockpit above the prop all’s well.
|
Wow, you rode the ferry in SD? It had been history a good while when I first attended ASW school there in 1970. Crikey, you must be older than me!
__________________
Rich Gano
FROLIC (2005 MainShip 30 Pilot II)
Panama City area
|
|
|
03-07-2021, 11:03 PM
|
#15
|
Guru
City: Concrete Washington State
Vessel Name: Willy
Vessel Model: Willard Nomad 30'
Join Date: Oct 2007
Posts: 18,743
|
Rich,
The ferrys were known as the nickel snatchers. I was there in the early 60’s. The boats called ferries were about 50’ long, wood planked, much like an old rowboat. Powered by a very loud 6-71. Yea I’m old but that means I’ve been young longer than you.
__________________
Eric
North Western Washington State USA
|
|
|
03-08-2021, 05:11 AM
|
#16
|
Senior Member
City: Green Cove Springs, Florida
Join Date: Feb 2012
Posts: 344
|
The specs below are for a new installation. Buships Technical Manual advises 2" shafts should have minimum clearance of .017, maximum of .091. The maximum clearance is very generous.
In many cases misalignment is evident if you check the clearances around the bearing ends. If/when you decide to change it be prepared to realign the engine, strut or both. Also, the prop shaft may be worn where it rides in the bearing. It may still have a little clearance with a new bearing.
Quote:
Originally Posted by Comodave
The ABYC guide for my 2” shafts says from a minimum of .005” to a maximum of .010”. It depends on what size shaft you are referring to but 1/16” is out of specs for most of our shaft sizes. The surveyor used a plastic set of feeler gauges that would bend to match the shaft OD to measure the clearance.
A 1.5” shaft goes from .004 to .009”.
A 2.5” shaft goes from .005 to .011.
Per the chart the surveyor included on my boats survey.
|
|
|
|
03-08-2021, 06:19 AM
|
#17
|
Senior Member
City: Manasquan NJ
Vessel Name: Mayrose
Vessel Model: Mainship 34 pilot
Join Date: Nov 2017
Posts: 150
|
Is clearance in the centered position. So if I can jack the shaft .045" is my clearance .0225"?
Thanks
Greg
|
|
|
03-08-2021, 07:40 AM
|
#18
|
Guru
City: Southport, FL near Panama City
Vessel Name: FROLIC
Vessel Model: Mainship 30 Pilot II since 2015. GB-42 1986-2015. Former Unlimited Tonnage Master
Join Date: Oct 2007
Posts: 4,984
|
Quote:
Originally Posted by Nomad Willy
Rich,
The ferrys were known as the nickel snatchers. I was there in the early 60’s. The boats called ferries were about 50’ long, wood planked, much like an old rowboat. Powered by a very loud 6-71. Yea I’m old but that means I’ve been young longer than you.
|
I love your altitude!
__________________
Rich Gano
FROLIC (2005 MainShip 30 Pilot II)
Panama City area
|
|
|
03-08-2021, 08:51 AM
|
#19
|
Guru
City: Concrete Washington State
Vessel Name: Willy
Vessel Model: Willard Nomad 30'
Join Date: Oct 2007
Posts: 18,743
|
Rich,
I have other attitudes if you’d care to hear.
__________________
Eric
North Western Washington State USA
|
|
|
03-08-2021, 12:05 PM
|
#20
|
Guru
City: Southport, FL near Panama City
Vessel Name: FROLIC
Vessel Model: Mainship 30 Pilot II since 2015. GB-42 1986-2015. Former Unlimited Tonnage Master
Join Date: Oct 2007
Posts: 4,984
|
Quote:
Originally Posted by Nomad Willy
Rich,
I have other attitudes if you’d care to hear.
|
I have lsel areno doubt. Why else are we all here?
__________________
Rich Gano
FROLIC (2005 MainShip 30 Pilot II)
Panama City area
|
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Trawler Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|