vibration at high rpm

The friendliest place on the web for anyone who enjoys boating.
If you have answers, please help by responding to the unanswered posts.

GLENNL

Member
Joined
Sep 27, 2017
Messages
17
Location
USA
Vessel Name
POWERPLAY II
Vessel Make
MAINSHIP 30 PILOT
My mainship 30 pilot has a prop vibration at high rpm's was told this was a clearance problem on this model does anyone know the fix
 
If you have a three blade propeller you could change to a four blade as this commonly reduces the diameter by around 6 to 8% keeping the same/similar RPM, they also tend to be smoother in most cases,(although normally found on larger vessels)

You could talk to a propeller expert about reducing diameter and increasing pitch again vessel/engine considerations

Other fixes include having a longer prop shaft normally moving the prop away from the hull as it sloops upwards toward the stern, this obviously depends on the hull shape and location of stern bearings or P brackets in relation to the propeller as these distances are critical ( normally only around 1 1/2 times the shaft diameter) so it dosent normally work out with out major works
 
Putting lead or concrete on the inside of the hull right above the prop would probably have a significant effect. Only a small dia area right above the prop would need the weight and I'm guessing it should be firmly affixed to the inside of the hull. Epoxy or perhaps 3M5200 comes to mind. May be nice to be removable but probably not. One could just put lead shot in a bag on the hull to see if it was going to work. Pices of steel plate 1 1/2 to 2" square laid in thick epoxy is another idea. Probably galvanized first.
 
Could be nature of the beast. Prop noise. If you have a full keel ahead of the prop, it will put disturbed water into the prop and it will be noisy when at higher speeds. Different props (more blades) can help, but it is hit and miss and expensive to experiment.
 
The propeller vibration issues with that model are well documented, and I believe there was a factory "fix." The traditional "rule of thumb" for tip clearance is around 15% of propeller diameter. Many boats with tunnels reduce this clearance because it increases thrust by creating a partial Kort effect making the boat a little faster. It also causes propeller driven vibration and sometimes "tunnel burn" where some bottom paint just won't stay on the bottom in the vicinity of the prop.

I found this is a quick search along with plenty of other sources:

BoatUS - Boat Reviews - Mainship Pilotâ„¢ 30

"In its first year of production the Pilot™ 30 encountered noise and vibration problems particularly on boats equipped with larger Yanmar engines. The cause seemed to be insufficient propeller tip clearance and was addressed and repaired under warranty by Mainship."

Propeller change by adding a blade and reducing diameter or prop shop modification of diameter and pitch are two methods. Many also suggest "keel fairing" where the back of the keel is modified to a taper instead of being "square" to "clean" waterflow to the prop. These have been mentioned above and are sound advice.

Concrete is an old school method of adding mass over the propeller to reduce propeller induced vibration. The modern concrete replacement is known as "Navy Tiles" which absorb vibration. I consider this a band aide as it does not address the root problem, tip clearance.

:socool:
 
Not so ...
The "problem" is vibration.
 
Just curiuos is it a new condition, cutlass worn?
 
Not so ...
The "problem" is vibration.

If the cause of the vibration is insufficient prop tip clearance, then I'd rather eliminate the cause than mitigate its effects. One is a cure, the other is a method to mask this effect.

No telling what wear this is vibration is also causing to other running gear components like cutlass bearings, rudder posts and props.
 
Al,
If the problem is vibration from prop blade tips being too close to the hull right above the prop then if you can stop the vibration the close blade tips are no longer a problem.
 
But you're not stopping it. You're trying to counterbalance the worst of it through the hull after it has already passed through portions of the hull. It's the remnants vibrating through the rest of the hull/components that still have an effect.

If you stop the source, you don't have to be worried about the rest.
 
thanks all, just bought the boat in july been there since will address this next week when i haul out for the winter , again thanks
 
The hassle is GRP construction is easy to create strong enough , but difficult to create stiff enough.

IF concrete stiffens the vibrating hull enough to be silent,, why not?

Its way cheaper than a 4 or 5 blade prop which may not solve the hull flexing .
 
The Pilot 30 is a Downeast planing hull. Concrete may be an old school fix for a full displacement hull, but the additional weight so far aft would probably have a negative effect on trim both static and underway.

I've been in plenty of old Feadships and Burgers with concrete in the bilge. In my own humble opinion for this vessel concrete would not be a good solution.

$0.02 :socool:


The hassle is GRP construction is easy to create strong enough , but difficult to create stiff enough.

IF concrete stiffens the vibrating hull enough to be silent,, why not?

Its way cheaper than a 4 or 5 blade prop which may not solve the hull flexing .
 
Keys,
The weight I was talking about would only be for material over an area perhaps only about 1 sq ft. It's hard to express oneself accurately on forums. I get wordy enough as it is.

But re this problem prop clearence is golden.
 
The logical start point is to have the propeller, shaft, bearings and alignment checked.
Having just bought the boat in July, you have no way of knowing what's gone on down there in the past.
Groundings, running over debris, even mishandling on shore may have occurred.
If all's well along the drive train, then it's time to look into some of the above recommendations.
 
Called marlow, they wouldn't give me any information, perhaps they think i want something for free not the case i do believe a five bladed prop may be the solution i just want to get it right the first time
 
Marlow probably doesn't really know anything since they were not around when the 30 was designed and built.
Listen to Keys he's been around Mainships and the owners groups for a very long time. This is a well documented problem with that model.
 
does everyone responding have Gerr's book?

If the cutlass is not a mess, and the prop is balanced, what you have is the blades causing high then low pressure pulses against the hull. The closer the tips, the thinner the hull, the more the vib. The vib is the hull flexing.
He recommends 15% on 1000 prop rpm and 10% can work from 300 to 1800 rpm. But those are guides. He admits pushing the dia further has benefit for low speed handling on low speed craft, but will increase the tendency for noise.

As reported before, you can make up some loss of dia with more blades, Gerr also recommends a bit of skew.

Of course, you could stiffen the hull in that area. Doesn't necessarily need lead, concrete, etc. We are in the modern age, with cored composites that might add enough stiffness to keep the vib and noise down. Sounds highly experimental to me, depending on the complexity of the inside surfaces involved. Certainly lightweight methods could work, my earplugs don't contain lead.:)
 
Last edited:
A good prop shop will let you try different props if their first recommendation doesn't work.
I do agree with checking everything else before assuming the prop needs to change.
 
thanks everyone, just hoping someone who reads this has had the same problem and what they did to solve it again thanks
 
To the OP:

Even if someone chimes in and says, "Yes I had the problem and this is what solved it", how do you know that his fix will fix your problem.

You are pinning your hopes on the high speed vibration problem being endemic to all boats like yours and someone else's fix will fix your boat. That may or may not be the case.

I have a Pilot 34. It has a little high speed vibration, probably cavitation. Someone else on this or another forum said fairing the dead wood solved his problem. I spent more than a thousand dollars doing the same thing and it did nothing for the vibration.

So be careful about the magic bullet solution.

As others have recommended, I would check the engine alignment, coupler, prop shaft straightness, prop trueness and key placement first. All of these can be done for a couple of hours of mechanic's time and a quick dive or haulout.

Then and only then would I consider the prop solution. I would talk to a good prop shop about what current prop to hull clearance you have and solutions like a 5 blade prop to improve it. But that will cost you a couple of thousand for a new prop.

Check the simple stuff first.

David
 
Check the torque on all your driveline bolts..

I had a similar problem and that fixed it. They had vibrated loose over time(a couple at the coupling).
 
The logical start point is to have the propeller, shaft, bearings and alignment checked.
Having just bought the boat in July, you have no way of knowing what's gone on down there in the past.
Groundings, running over debris, even mishandling on shore may have occurred.
If all's well along the drive train, then it's time to look into some of the above recommendations.

This was going to be my comment. Go on the hard, pull the prop, shaft and check cutlass and other bearings. Then have the yard put it all back together . You at least eliminate the obvious first.

To the OP:

Even if someone chimes in and says, "Yes I had the problem and this is what solved it", how do you know that his fix will fix your problem.

You are pinning your hopes on the high speed vibration problem being endemic to all boats like yours and someone else's fix will fix your boat. That may or may not be the case.

I have a Pilot 34. It has a little high speed vibration, probably cavitation. Someone else on this or another forum said fairing the dead wood solved his problem. I spent more than a thousand dollars doing the same thing and it did nothing for the vibration.

So be careful about the magic bullet solution.

As others have recommended, I would check the engine alignment, coupler, prop shaft straightness, prop trueness and key placement first. All of these can be done for a couple of hours of mechanic's time and a quick dive or haulout.

Then and only then would I consider the prop solution. I would talk to a good prop shop about what current prop to hull clearance you have and solutions like a 5 blade prop to improve it. But that will cost you a couple of thousand for a new prop.

Check the simple stuff first.

David

Good advice....
 
Back
Top Bottom