Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-16-2019, 11:54 AM   #1
Veteran Member
 
City: Morehead City, NC
Join Date: May 2019
Posts: 50
Sea water pump impeller

Hello again everybody. I have a 77 Mainship with a Perkins 6.354T. I am about to undertake an impeller change and I thought I would go online and find one and have it ready. Can anybody advise what kind of sea water pump I have? Also, is there a difference in the quality of the impellers ie cheap vs expensive, brand preference? Mine is near the lower starboard under the heat exchanger and appears to be a pain in the butt to get to. Can this be replaced without taking off the heat exchanger and maybe just reaching way down and removing the pump cover sliding the old one out and the new one in? Looking for shortcuts and advice. Thanks everybody.
Gaylord Ballard is offline   Reply With Quote
Old 08-16-2019, 01:34 PM   #2
Senior Member
 
Solly's Avatar
 
City: Solomons MD.
Vessel Name: Sun Runner
Vessel Model: 1985 Mainship 34 Trawler MK III
Join Date: Mar 2018
Posts: 488
Following... I have to do this too.

I'd do a search for the impeller. Perkins, T6.354. marine... Should only be 1 pump fitted. At least I've never heard any different...
Solly is offline   Reply With Quote
Old 08-16-2019, 01:49 PM   #3
Guru
 
Pete Meisinger's Avatar
 
City: Oconto, WI
Vessel Name: Best Alternative
Vessel Model: 36 Albin Aft Cabin
Join Date: Oct 2012
Posts: 3,145
The only thing I can tell you about impellers is this:
1) To get them out use two screwdrivers and pry from opposite sides at the same time. You don't want to use pliers because you will tear out pieces which could end up in your system.
2) Note the direction of the bend in the blades, on some it is possible to put them in backwards.
3) Lube the casing with dish soap or antifreeze or KY jelly before you slide the new impeller in.
4) If the brass front plate is showing wear or groves you should replace it. They are often reversible.

Even if they are hard to get to it really isn't a very tough job.

pete
Pete Meisinger is offline   Reply With Quote
Old 08-16-2019, 02:03 PM   #4
Guru
 
City: Boston
Vessel Name: Adelante
Vessel Model: IG 30
Join Date: Nov 2016
Posts: 1,611
If there isn't enough room for 2 screwdrivers, screw 2 drywall screws into the impeller and then use pliers. I bought a bottle of glycerin at CVS to lube impellers.
I put a tie wrap around one end to bend the vanes the right way and make the dia small enough to insert it easily.
Buy some spare front plate screws. They are soft brass and damage easily, and will disappear into the dark recesses of the bilge if dropped.
SoWhat is offline   Reply With Quote
Old 08-16-2019, 02:40 PM   #5
Moderator Emeritus
 
Comodave's Avatar
 
City: Au Gres, MI
Vessel Name: Black Dog
Vessel Model: Formula 41PC
Join Date: Jul 2015
Posts: 21,191
My starboard engine is very difficult to replace the impeller. I have a Jabsco impeller puller that I use an all thread rod instead of the T handle that came with it. It works great to get the old impeller out. To get the new one in I have a tool from impellertool.com. It is a machined tube with a funnel on one end. You lube up the impeller and twist it into the end with the funnel. Then the whole tube slides into the pump without the impeller dragging on the sides of the pump. Then hold the impeller in place and pull the tube out. Easy peasy. Simple to install the new impeller. No affiliation with the company, just a very satisfied customer. It makes it possible for me to swap the impeller.
__________________
Boat Nut:
If you are one there is no explanation necessary.
If you aren’t one, there is no explanation possible.
Comodave is online now   Reply With Quote
Old 08-16-2019, 02:47 PM   #6
Guru
 
Gulf Comanche's Avatar
 
City: Baton Rouge, Louisiana
Vessel Name: Old School
Vessel Model: 38' Trawler custom built by Hike Metal Products
Join Date: Dec 2007
Posts: 1,045
I use the pliers that turn 90* from the handle, grab hold of both sides of the middle part and start wobbling the impeller while pulling out. Use the lube that comes with the new one. Don’t worry about which way the vanes go back in because they’ll correct themselves when you crank the engine.
Gulf Comanche is offline   Reply With Quote
Old 08-16-2019, 03:05 PM   #7
Senior Member
 
sledge's Avatar
 
City: Eastcoast
Vessel Model: American Tug 41
Join Date: Sep 2018
Posts: 254
I've done this a few times on two different engines, you should not have to remove the heat exchanger; if you do, wow i would hate to have that kind of setup.
The first time is a little disconcerting but it gets easier every time after that. If you do use two screwdrivers as someone suggested, just take care not to gouge the inner sides inside the pump walls. For one of our pumps, i use a removal tool like ComoDave mentioned, i think the one I use was made by SeaDog; they are a relatively cheap investment that makes life a lot easier, but it needs to be sized properly for your specific impeller. It looks like this:
Attached Images
 
sledge is offline   Reply With Quote
Old 08-16-2019, 03:17 PM   #8
Moderator Emeritus
 
Comodave's Avatar
 
City: Au Gres, MI
Vessel Name: Black Dog
Vessel Model: Formula 41PC
Join Date: Jul 2015
Posts: 21,191
My impeller removal tool looks very similar to that. I can’t use the T handle because the T hits a pipe on my engine. I got a piece of all thread, metric thread of course, and put on double nuts and use them to turn the all thread. Works great. My heat exchanger make the pump not visible. So without the tools I could not even change the impeller. The PO’s mechanics used to pull the pump to change the impeller, what a PITA. Now I can do it in less than 30 minutes.
__________________
Boat Nut:
If you are one there is no explanation necessary.
If you aren’t one, there is no explanation possible.
Comodave is online now   Reply With Quote
Old 08-16-2019, 03:45 PM   #9
Guru
 
jleonard's Avatar
 
Join Date: Jun 2008
Posts: 5,037
You probably have a Sherwood RPBC pump.
Here's a drawing
Attached Files
File Type: pdf SherwoodRP-B-C pump.PDF (60.2 KB, 25 views)
__________________
Jay Leonard
Ex boats: 1983 40 Albin trunk cabin, 1978 Mainship 34 Model 1
New Port Richey, Fl
jleonard is offline   Reply With Quote
Old 08-16-2019, 07:43 PM   #10
Senior Member
 
Solly's Avatar
 
City: Solomons MD.
Vessel Name: Sun Runner
Vessel Model: 1985 Mainship 34 Trawler MK III
Join Date: Mar 2018
Posts: 488
1 more tip I've heard.
Spread something under the pump 1st.
Towel, piece of plastic.
Won't lose the screws or the key into the bilge.

Last time I was on the boat I looked at where mine is on the engine..
Said "Not today"........
Solly is offline   Reply With Quote
Old 08-17-2019, 07:21 AM   #11
Guru
 
jleonard's Avatar
 
Join Date: Jun 2008
Posts: 5,037
An by the way, pay attention to the phenolic "coupler" that drives the pump. Mine (many years ago) was pretty well shot. I could not find one anywhere.
Luckily I had access to a machine shop and had one made.
__________________
Jay Leonard
Ex boats: 1983 40 Albin trunk cabin, 1978 Mainship 34 Model 1
New Port Richey, Fl
jleonard is offline   Reply With Quote
Old 08-17-2019, 08:11 AM   #12
Guru
 
Datenight's Avatar
 
City: Groton, CT
Vessel Name: Datenight
Vessel Model: North Pacific 45
Join Date: Jan 2008
Posts: 1,106
Quote:
Originally Posted by jleonard View Post
An by the way, pay attention to the phenolic "coupler" that drives the pump. Mine (many years ago) was pretty well shot. I could not find one anywhere.
Luckily I had access to a machine shop and had one made.

Was it Brian at Watrous Brothers? What a great guy.

Rob
__________________
North Pacific 45
Datenight is offline   Reply With Quote
Old 08-17-2019, 08:17 AM   #13
Guru
 
jleonard's Avatar
 
Join Date: Jun 2008
Posts: 5,037
Quote:
Originally Posted by Datenight View Post
Was it Brian at Watrous Brothers? What a great guy.

Rob
No. It was the machine shop where I worked.
A "government job".
__________________
Jay Leonard
Ex boats: 1983 40 Albin trunk cabin, 1978 Mainship 34 Model 1
New Port Richey, Fl
jleonard is offline   Reply With Quote
Old 08-17-2019, 08:25 AM   #14
Guru
 
Datenight's Avatar
 
City: Groton, CT
Vessel Name: Datenight
Vessel Model: North Pacific 45
Join Date: Jan 2008
Posts: 1,106
Just as good I'm sure! If you ever need work in Mystic Brian is the man.

Rob
__________________
North Pacific 45
Datenight is offline   Reply With Quote
Old 08-18-2019, 06:46 AM   #15
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
Sometimes the screws holding the cover plate are hard to access.

Replace the screws with SS hex head Allen wrench style , from the local hardware store.

Buy extras so should you drop a couple , its no biggie.
FF is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 02:56 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012