LEHMAN 120- exhaust presure in coolant system

The friendliest place on the web for anyone who enjoys boating.
If you have answers, please help by responding to the unanswered posts.

wonderfulwade

Veteran Member
Joined
Dec 8, 2015
Messages
44
Location
USA
Vessel Name
LAZY LIBRA
Vessel Make
Marine Trader 44
Bought my boat in the FL panhandle. Had mechanic do oil changes to bring her home to Charleston. He called to inform me starboard engine ran hot while warming her up and had milky oil. I went down and cleaned all coolers/exchangers. replaced all hoses, rebuilt raw water pump and replaced head gasket and head refurbished. With head off saw some pitting in 2nd cylinder from front as if water had been getting in there for a while, also the mechanic had concerns that that cylinder may have a hairline crack although I couldn't tell a difference from the others. He took a torch into the cylinder trying to raise water beads in the suspect area but never found any. The head checked out good and we never could prove the head gasket failed although it was degraded around that cylinder (could of been from disassembly). I reassembled the engine. After firing her up it was obvious I had air bubbles in my coolant reservoir although engine ran perfect, no coolant in oil, coolant level good, no hot/cool spots on infrared thermometer. Decided to bring her home. Engine ran great but.......about every 20 hours of run time I had to add a gallon of coolant.....we made the 1000 mile trip home and now I have her blocked up for refit. After a few days of sitting up, the engine was hydro locked and the coolant was low. After draining the coolant and letting her sit 24 hours it fires right up. At first I suspected the block must be cracked but after talking to American diesel, he feels this is unlikely and the first thing to check is the exhaust manifold......Boy! am I a dumb A$$....this never occurred to me but makes perfect sense considering my symptoms. I know this is a long post but I have to figure this out and didn't want to leave out any details. If in fact the engine needs to come out I want to get-r-done before tackling all the other 5986 things I have to do to this old girl. I have the manifold out and am pretty mechanically inclined. What technique would be best to check out this manifold? Sound like I'm on the right track?
 
How would one rebuild a non-liner engine in a boat sir? Especially one with a potential crack in the cylinder. I love learning new things.

I thought the crack was in the manifold not the block?

"At first I suspected the block must be cracked but after talking to American diesel, he feels this is unlikely and the first thing to check is the exhaust manifold."
 
Last edited:
if it turns out a cracked manifold........no rebuild necessary......
 
lacking any better ideas you can use rubber plumbing caps and clamps add a Schrader valve and pump air into the water side while in a water tank looking for bubbles or pressure loss.
 
Exhaust manifold best tested using water under pressure in cooling jacket. Just cap off and plug all ports and hose fittings but one, attach a water source there. I use my well pump which I adjust p-switch to 30psi for the test. Leave water under pressure with manifold set on blocks so you can observe the exhaust ports. Looking for water to drip out. Assuming manifold is off the engine.
 
Bayview and Ski

Seen it where cracked heads and manifolds only show leak when up to temperature, pressure test not always revealing on a cold engine. Magna flux on cold parts certainly can show all.

To the OP, did you do a mechanical survey prior to purchase or is this a new problem?
 
Agreed, water test of the manifold is "inconclusive" if no leak found. It IS conclusive if a leak is found.

Another bit: A leaky exhaust manifold on a NAT engine will not cause bubbles to show up in coolant. Not enough pressure in manifold to leak from ex side to coolant side. Bubbles in coolant means there is leak from combustion chamber into coolant. Head, head gasket, cracked cyl are the poss culprits. Cylinders should be checked with dye penetrant test with pistons lowered into bores, can test two at a time. Head off to test, of course.

And get the water out of the oil sump and get any milky oil out. That stuff will ruin bearings given enough time.
 
I have these exact symptoms on my Lehman. Just finished head. Bubbles in coolant. American diesel said it’s probably manifold. How’s you make out?
 
I have these exact symptoms on my Lehman. Just finished head. Bubbles in coolant. American diesel said it’s probably manifold. How’s you make out?

This is a 6 year old thread, you likely will not get an answer. Maybe start a new thread? And welcome aboard.
 
Haha yeah you’re probably right. No one ever posts results, but I’m in same shoes so figured I’d ask
 
I had bubbles in coolant. Did a head job and head gasket after pressure testing and getting no manifold leak.

Lasted 100 hrs but bubbles returned. Thinking minor imperfection on block top I must hsve misses.

Ran engine for another 1500 or so hours with no overtemp, no coolant in oil and no coolant loss.

Enough exoerts told me until something else showed, like oil sample anomoly or anything...stop worrying and cruise.

Never was happy about it but being paranoid about failure was foolish as it just kept chugging along.
 
Thanks buddy! I appreciate the input. I think I have the same situation. I saw a guy saying to smear some permeated # 2 on the metal gasket for imperfections. Obviously those of us with a certain sort of brain obsess over things that don’t need to be worried about. 1500 hours is a long time for no issues. Thanks again for your hard earned knowledge.
 
Back
Top Bottom