Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-13-2015, 12:11 AM   #1
Guru
 
City: Galveston, Texas
Vessel Model: 24" El Pescador
Join Date: Nov 2014
Posts: 744
Walter V-Drive

Anyone know anything about a Walter V-Drive?
Looked at a boat today-Cat engines far astern and put in backwards with shaft going forward to transmission and then propeller shaft going aft to propeller.

Provided a lot more space in the engine room by getting it out from under the saloon/salon floor.
Is this a good piece of machinery? Cause any additional problems?

Thanks
Ken
ktdtx is offline   Reply With Quote
Old 08-13-2015, 02:03 AM   #2
Guru
 
kapnd's Avatar
 
City: hawaii
Vessel Name: #31
Vessel Model: ex-Navy MUB 50 fish/cruise
Join Date: Aug 2013
Posts: 873
Sounds like this is a modification to the boat?
If so, you should get a competent surveyor's report on the mechanical parts, their compatibility and correct installation, and an engineering assessment of the changes made. Remote V-drives require considerable expertise to be correctly installed. (Nothing wrong with the concept, but does present challenges for the installer)
Moving the engines can have big effect on performance, safety, and the way the boat handles.
What kind of boat, what engines, what V-drives???
Pictures??
Just recalled an earlier thread on here where the boatowner was asking why his exhaust outlets were partially submerged, this would be the first thing I would look at. It will say much about how well the job was engineered, and whether or not you should continue your interest in the vessel.
kapnd is offline   Reply With Quote
Old 08-13-2015, 02:33 AM   #3
Guru
 
City: Galveston, Texas
Vessel Model: 24" El Pescador
Join Date: Nov 2014
Posts: 744
I think it is a "from the factory" installation.
It's a Canoe Cove 53' with 375 hp Cat 3208's

Ken
ktdtx is offline   Reply With Quote
Old 08-13-2015, 03:37 AM   #4
Guru
 
siestakey's Avatar
 
City: Sarasota,FL/Thomasville,GA
Vessel Name: Steppin Stone IV
Vessel Model: Marine Trader Kelly Trawler 46
Join Date: Jul 2013
Posts: 1,815
I do Not know much about them but when I was looking at boats ran across one did a little research on them

Called the factory and they still stocked parts for it
siestakey is offline   Reply With Quote
Old 08-13-2015, 05:38 AM   #5
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
Walter has a great reputation.
FF is offline   Reply With Quote
Old 08-13-2015, 05:47 AM   #6
Guru
 
O C Diver's Avatar
 
City: Fort Myers, FL... Summers in the Great Lakes
Vessel Name: Slow Hand
Vessel Model: Cherubini Independence 45
Join Date: Dec 2010
Posts: 12,834
Have seen a couple of boats with them. Don't neglect oil changes. Friend who had a pair of them in a sport fish tied to a pair of Cummins had one fail. Don't remember if they rebuilt or replaced it. Not sure if he ever changed the oil in it. Stereotypical twin engine owner, "fix what breaks; I have 2 engines so I can always get home".

Like the concept better in low HP applications like trawlers. One think to look at carefully is the location of the stuffing box. Having it under the engine can be a real PIA to repack or tighten.

Ted
__________________
Blog: mvslowhand.com
I'm tired of fast moves, I've got a slow groove, on my mind.....
I want to spend some time, Not come and go in a heated rush.....
"Slow Hand" by The Pointer Sisters
O C Diver is offline   Reply With Quote
Old 08-13-2015, 07:57 AM   #7
Guru
 
Codger2's Avatar
 
City: San Diego
Vessel Name: Circuit Breaker
Vessel Model: 2021..22' Duffy Cuddy cabin
Join Date: Oct 2007
Posts: 6,691
Mikelson Yachts have used similar drive systems for years with great success.

The Advantages of a V-Drive | Boating Magazine
__________________
Done with diesel power boats! Have fallen in love with all electric!
Codger2 is offline   Reply With Quote
Old 08-13-2015, 09:28 AM   #8
Senior Member
 
capt jerry's Avatar
 
Join Date: Oct 2007
Posts: 323
Quote:
Originally Posted by Codger2 View Post
Mikelson Yachts have used similar drive systems for years with great success.

The Advantages of a V-Drive | Boating Magazine
i have delivered a 50 ft sea ray to florida from ny many times and it had V drives never a problem
capt jerry is offline   Reply With Quote
Old 08-13-2015, 10:54 AM   #9
Guru
 
ranger58sb's Avatar
 
City: Annapolis
Vessel Name: Ranger
Vessel Model: 58' Sedan Bridge
Join Date: Aug 2013
Posts: 7,088
V-drives are quite common in express boats (Sundancers and Cruisers and so forth), and Walter's version has a good reputation.


They speak to the trade-off between user space (room for that extra mid-cabin berth) versus access to propulsion-related systems...


-Chris
__________________
Chesapeake Bay, USA
ranger58sb is offline   Reply With Quote
Old 08-13-2015, 12:12 PM   #10
Guru
 
City: Galveston, Texas
Vessel Model: 24" El Pescador
Join Date: Nov 2014
Posts: 744
Thanks all.

Somehow came here before Google and their website shows a company in business since 1927.

The Walter Machine Machine Co., Inc.
ktdtx is offline   Reply With Quote
Old 08-13-2015, 06:49 PM   #11
Veteran Member
 
windled's Avatar
 
City: Manotick, Ontario
Vessel Name: The Emerald
Vessel Model: Silverton 31C
Join Date: Apr 2015
Posts: 55
If it's of any use, I have a few of the original manuals for my Silverton 31C scanned and uploaded to my company server, here:
Index of /dalewindle


Includes the Walter V drive manual for my boat. They have been problem free.
__________________
Captain Dale Windle
Manotick, Ontario, Canada
1986 Silverton 31C
windled is offline   Reply With Quote
Old 08-13-2015, 07:24 PM   #12
Senior Member
 
djones44's Avatar
 
City: Port Moody
Vessel Name: Twilight1
Vessel Model: Permaglass Sedan
Join Date: Apr 2012
Posts: 217
Quote:
Originally Posted by ktdtx View Post
I think it is a "from the factory" installation.
It's a Canoe Cove 53' with 375 hp Cat 3208's

Ken
Yes, I have them on a Canoe Cove 37, and have had them in various boats for 40 years. In the 70's they would clatter when trolling, but today they are so smooth that they seem to engage transparently. And I do have a full basement between them and the V-berths on the CC37 as one consequence, with no diesels in the main salon when cruising. I have 500hp to lift them out when planing too, an ideal power setup with that weight well aft.

Walters are the best.
djones44 is offline   Reply With Quote
Old 08-14-2015, 02:13 AM   #13
Guru
 
City: Galveston, Texas
Vessel Model: 24" El Pescador
Join Date: Nov 2014
Posts: 744
Thanks again and Dale I scanned your file and they appear to be a minimum maintenance item.

Ken
ktdtx is offline   Reply With Quote
Old 08-15-2015, 11:52 AM   #14
Guru
 
Old deckhand's Avatar
 
City: Sitka
Vessel Model: Transpacific Marine Eagle 32
Join Date: Dec 2014
Posts: 519
Owned a boat with one and my 35 inch sleeve was too short to reach the stuffing box. Also I believe I read on boat diesel that it takes additional horse power to turn it.
Old deckhand is offline   Reply With Quote
Old 08-15-2015, 12:16 PM   #15
Guru
 
kapnd's Avatar
 
City: hawaii
Vessel Name: #31
Vessel Model: ex-Navy MUB 50 fish/cruise
Join Date: Aug 2013
Posts: 873
Yes, stuffing box access can be an issue. Funny that designers don't seem to see such issues.
I have cursed them loudly many a time, some boats have left the shop with less than perfect alignment because of this.
Horsepower loss is negligible, you wouldn't notice it.
kapnd is offline   Reply With Quote
Old 08-15-2015, 02:50 PM   #16
Ted
Guru
 
Ted's Avatar
 
City: Campbell River
Vessel Name: Okisollo
Join Date: Apr 2012
Posts: 783
Anytime you add something you increase complexity, potential failure points and
maintenance.
However if sized right they can have advantages.
Lots of testing in drag boats. Think over-sized shingle with massive V-8 mounted
in the stern with long shaft to the V-drive under the pilot's (hopefully controller)
seat forward.

Ted
Ted is offline   Reply With Quote
Old 08-15-2015, 08:26 PM   #17
Senior Member
 
capt jerry's Avatar
 
Join Date: Oct 2007
Posts: 323
Quote:
Originally Posted by Ted View Post
Anytime you add something you increase complexity, potential failure points and
maintenance.
However if sized right they can have advantages.
Lots of testing in drag boats. Think over-sized shingle with massive V-8 mounted
in the stern with long shaft to the V-drive under the pilot's (hopefully controller)
seat forward.

Ted
i had a friend jn up state ny that had a wooden boat built before ww2 that had a packard engine with a walters v dr never a problem i met him in 1970 and it was still running
capt jerry is offline   Reply With Quote
Old 08-15-2015, 10:26 PM   #18
Guru
 
Nomad Willy's Avatar
 
City: Concrete Washington State
Vessel Name: Willy
Vessel Model: Willard Nomad 30'
Join Date: Oct 2007
Posts: 18,743
The V drive has some attractive advantages.

Much more desirable if running light engines. Big heavy diesels belong amidships IMO for good weight ballance. Moving weight fwd (to counter the aft engines) produces a boat reluctant to follow seas pitch wise and could be wet running boats. Or worse. Amidship engines will probably produce a more level running boat w a smoother ride and depending on hull design may be more efficient.

But the noise and space benifits are obvious. The hull should be designed for the aft weight and I'd be very suspicious of a conversion unless the original boat had twin outdrives.
__________________
Eric

North Western Washington State USA
Nomad Willy is offline   Reply With Quote
Old 08-19-2015, 06:21 PM   #19
Guru
 
High Wire's Avatar
 
City: Cape May, NJ
Vessel Name: Irish Lady
Vessel Model: Monk 36
Join Date: Dec 2007
Posts: 4,964
I had a Carver 28 with Walter V-Drives. Never any trouble. Repacking the stuffing box was done hanging upside down. Not fun but doable when you are 25 years old!
__________________
Archie
Irish Lady
1984 Monk 36 Hull #46
Currently in Cape May, NJ
High Wire is offline   Reply With Quote
Old 08-31-2015, 09:30 AM   #20
Guru
 
City: Melbourne, FL
Join Date: Dec 2014
Posts: 1,731
Was this boat Aliyah III?
stubones99 is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 02:17 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012