Reply
 
Thread Tools Search this Thread Display Modes
 
Old 12-23-2013, 08:07 AM   #1
Guru
 
Moonstruck's Avatar
 
City: Hailing Port: Charleston, SC
Vessel Name: Moonstruck
Vessel Model: Sabre 42 Hardtop Express
Join Date: Nov 2008
Posts: 8,276
Hose Clamps

I mentioned these in another thread. during an engine room check, I discovered some rust stain under a hose clamp on the dripless shaft log. Upon further checking the screws on the clamps were starting to rust. Since there were 4 clamps on each shaft log, there were 8 to replace. I went to the local WM because of the late hour. Picked up clamps at $8.25 each. Started changing the clamps. They would start to feel snug, but would not tighten. One even just pulled out by hand.

The clamps did not look as usual, but they assured me that they were good. Instead of having cut outs for the screw threads they had been crimped. Took them back to WM and went to Marine Connection the next morning to pick up better clamps at $1.50 ea. I explained to the WM store that the clamps could cause a boat to sink. Please don't put them back in stock. They didn't seem verry concerned.

I am telling this to bring awareness about a possible problem. That was my experience. YMMV.
__________________
Don on Moonstruck
Sabre 42 Hardtop Express
When cruising life is simpler, but on a grander scale (author unknown)
https://moonstruckblog.wordpress.com/
Moonstruck is offline   Reply With Quote
Old 12-23-2013, 08:15 AM   #2
Guru
 
psneeld's Avatar
 
City: Ft Pierce
Vessel Name: Sold
Vessel Model: Was an Albin/PSN 40
Join Date: Oct 2011
Posts: 28,149
Quote:
Originally Posted by Moonstruck View Post
I mentioned these in another thread. during an engine room check, I discovered some rust stain under a hose clamp on the dripless shaft log. Upon further checking the screws on the clamps were starting to rust. Since there were 4 clamps on each shaft log, there were 8 to replace. I went to the local WM because of the late hour. Picked up clamps at $8.25 each. Started changing the clamps. They would start to feel snug, but would not tighten. One even just pulled out by hand.

The clamps did not look as usual, but they assured me that they were good. Instead of having cut outs for the screw threads they had been crimped. Took them back to WM and went to Marine Connection the next morning to pick up better clamps at $1.50 ea. I explained to the WM store that the clamps could cause a boat to sink. Please don't put them back in stock. They didn't seem verry concerned.

I am telling this to bring awareness about a possible problem. That was my experience. YMMV.
Actually the non-slit clamps are supposed to be better/stronger...but obviously they have to be made correctly....West is usually pretty insistent on carrying better than average and certainly not poor quality stuff.

I'm sure the higher ups in the company would be interested in both quality control and the lack of interest by the store (which doesn't surprise me for some but not most West employee's as they often seem caring even if pretty inexperienced with the merchandise).

If you care to pursue let me know...I used to have a contact in product testing...I would think he would be very interested.

AWAB LLC
Attached Images
 
psneeld is offline   Reply With Quote
Old 12-23-2013, 08:27 AM   #3
Guru
 
Moonstruck's Avatar
 
City: Hailing Port: Charleston, SC
Vessel Name: Moonstruck
Vessel Model: Sabre 42 Hardtop Express
Join Date: Nov 2008
Posts: 8,276
Quote:
Originally Posted by psneeld View Post
Actually the non-slit clamps are supposed to be better/stronger...but obviously they have to be made correctly....West is usually pretty insistent on carrying better than average and certainly not poor quality stuff.

I'm sure the higher ups in the company would be interested in both quality control and the lack of interest by the store (which doesn't surprise me for some but not most West employee's as they often seem caring even if pretty inexperienced with the merchandise).

If you care to pursue let me know...I used to have a contact in product testing...I would think he would be very interested.

AWAB LLC
I would be happy to discuss it with them. The problem seemed to be in the stainless stamping of whatever they would call the part that holds screw down on the clamp. I showed them that in the store. If the screw is not tight against the band, it will not hold. I was not going to trust my boat to that.
__________________
Don on Moonstruck
Sabre 42 Hardtop Express
When cruising life is simpler, but on a grander scale (author unknown)
https://moonstruckblog.wordpress.com/
Moonstruck is offline   Reply With Quote
Old 12-23-2013, 08:48 AM   #4
Guru
 
psneeld's Avatar
 
City: Ft Pierce
Vessel Name: Sold
Vessel Model: Was an Albin/PSN 40
Join Date: Oct 2011
Posts: 28,149
Quote:
Originally Posted by Moonstruck View Post
I would be happy to discuss it with them. The problem seemed to be in the stainless stamping of whatever they would call the part that holds screw down on the clamp. I showed them that in the store. If the screw is not tight against the band, it will not hold. I was not going to trust my boat to that.
seems like every other hose clamp I take off the screw backs out instead of the clamp loosening...makes me think of alternatives to expensive non-working items....
psneeld is offline   Reply With Quote
Old 12-23-2013, 09:55 AM   #5
Valued Technical Contributor
 
DavidM's Avatar
 
City: Litchfield, Ct
Join Date: Aug 2012
Posts: 6,786
The rusting hose clamps that you removed are the worst of the worse. They have a carbon steel screw with a perforated SS band.

The next better, but not good is a stainless steel screw with perforated band.

The best is a stainless steel screw, 316 SS band with no perforations, smooth inside and a rolled edge. AWAB makes these and are one of the best. Defender sells them in the $2-4.00 range depending on size.

The one you got from WM was probably Chinese made and they tried to get it right, but didn't.

David
DavidM is offline   Reply With Quote
Old 12-23-2013, 10:44 AM   #6
Guru
 
ancora's Avatar
 
Join Date: Dec 2007
Posts: 4,021
Now this here is a hose clamp. I get them at a chandlery where the pro's get their stuff, not WM. Not cheap but worth the peace of mind.
Attached Thumbnails
Hose Clamp 001.jpg  
ancora is offline   Reply With Quote
Old 12-23-2013, 11:14 AM   #7
Guru
 
skipperdude's Avatar
 
City: Whittier AK
Vessel Name: Apache II
Vessel Model: 1974 Donald Jones
Join Date: Oct 2007
Posts: 3,147
Quote:
Originally Posted by ancora View Post
Now this here is a hose clamp. I get them at a chandlery where the pro's get their stuff, not WM. Not cheap but worth the peace of mind.

I gotta get me some of those

SD
__________________
If you can't repair it maybe it shouldn't be on the boat
skipperdude is offline   Reply With Quote
Old 12-23-2013, 12:05 PM   #8
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
At your local big box house store they have screwdrivers that have inserts to change from small straight or Philips driver.

These handles with the bits out will fit most hex head hose clamps and are far better for tightening or adjusting .

Best $5.00 you will ever spend if the hose clamps are in a hard to reach spot.
FF is offline   Reply With Quote
Old 12-23-2013, 03:48 PM   #9
Senior Member
 
City: Seattle
Vessel Name: Poach
Vessel Model: Sabreline Trawler
Join Date: Aug 2013
Posts: 234
Quote:
Originally Posted by FF View Post
At your local big box house store they have screwdrivers that have inserts to change from small straight or Philips driver.

These handles with the bits out will fit most hex head hose clamps and are far better for tightening or adjusting .

Best $5.00 you will ever spend if the hose clamps are in a hard to reach spot.

I agree having the right tool makes a world of difference. I have a stand-alone hex nut driver that fits the clamps.
Poach is offline   Reply With Quote
Old 12-23-2013, 04:05 PM   #10
Guru
 
psneeld's Avatar
 
City: Ft Pierce
Vessel Name: Sold
Vessel Model: Was an Albin/PSN 40
Join Date: Oct 2011
Posts: 28,149
after seeing how many automotive companies have changed from traditional clamps to everything including tie wraps....and seeing how hard it is to remove the average hose on a fitting.....for those hoses under suction/low pressure I just wonder if ALL these clamps are just a waste of money....

I have come across probably hundreds or thousands of hoses with broken or loose clamps that never leaked a drop...makes you wonder....
psneeld is offline   Reply With Quote
Old 12-23-2013, 05:00 PM   #11
TF Site Team
 
City: Ex-Brisbane, (Australia), now Bribie Island, Qld
Vessel Name: Now boatless - sold 6/2018
Vessel Model: Had a Clipper (CHB) 34
Join Date: Jun 2008
Posts: 10,101
I'm with you there PS. I have no issues getting hoses on - only ever getting' em off…but...I have seen over-clamping actually cut through hoses.
__________________
Pete
Peter B is offline   Reply With Quote
Old 12-23-2013, 05:12 PM   #12
Guru
 
Forkliftt's Avatar
 
City: Diberville Mississippi
Vessel Name: KnotDoneYet
Vessel Model: 1983 42' Present Sundeck
Join Date: Oct 2007
Posts: 2,450
Quote:
Originally Posted by ancora View Post
Now this here is a hose clamp. I get them at a chandlery where the pro's get their stuff, not WM. Not cheap but worth the peace of mind.
T clamps are the best clamp ever, but sizing can be an issue as their min - max range is not as broad as a traditional hose clamp.
__________________
Steve Point Cadet/ Biloxi, Mississippi USA
*Present 42 twin 135 Lehmans
Forkliftt is offline   Reply With Quote
Old 12-23-2013, 07:37 PM   #13
Senior Member
 
MC Escher's Avatar
 
City: Central Ohio
Join Date: Sep 2013
Posts: 151
I know I'm new at this, but I'm surprised that A/N fittings aren't more common boats.
__________________
If God didn't want me to walk on the grass, he wouldn't have left it on the ground.
MC Escher is offline   Reply With Quote
Old 12-23-2013, 08:08 PM   #14
Valued Technical Contributor
 
DavidM's Avatar
 
City: Litchfield, Ct
Join Date: Aug 2012
Posts: 6,786
Hoses are hard to get off, but once you take them off they will often leak if you don't tighten down the hose clamp when you put them back on.

A few days ago I took off the raw water hose from the thruhull to the raw water pump. I had to really crank down on the hose clamp to get it to stop leaking when I put it back on.

Hmm, I think it was the perforated type. Better replace it.

David
DavidM is offline   Reply With Quote
Old 12-23-2013, 08:20 PM   #15
Guru
 
psneeld's Avatar
 
City: Ft Pierce
Vessel Name: Sold
Vessel Model: Was an Albin/PSN 40
Join Date: Oct 2011
Posts: 28,149
when hoses and barb fitting are new...they are almost like push-lock fittings these days...once on...you have to cut them off to adjust...

I'm not too worried about leaks as long as I keep my hoses and fittings fresh...I'd rather feel good about them than worry if a clamp is up to specs or fatigued or rusting without me knowing it.
psneeld is offline   Reply With Quote
Old 12-24-2013, 01:07 AM   #16
TF Site Team
 
City: Ex-Brisbane, (Australia), now Bribie Island, Qld
Vessel Name: Now boatless - sold 6/2018
Vessel Model: Had a Clipper (CHB) 34
Join Date: Jun 2008
Posts: 10,101
Quote:
Originally Posted by djmarchand View Post
Hoses are hard to get off, but once you take them off they will often leak if you don't tighten down the hose clamp when you put them back on.
David
Huh…I've never managed to get a hose on the boat off yet and be able to put it back on. I've had to cut it to free it every time.
__________________
Pete
Peter B is offline   Reply With Quote
Old 12-24-2013, 03:58 AM   #17
Moderator Emeritus
 
Bay Pelican's Avatar
 
City: Chicago, IL
Vessel Name: Bay Pelican
Vessel Model: Krogen 42
Join Date: Oct 2007
Posts: 2,993
Pete have you tried a heat gun and either a flat head screw driver or a channel lock pliers? I have yet to have to cut off a hose, although I have done so when I was discarding the hose.

Marty
Bay Pelican is offline   Reply With Quote
Old 12-24-2013, 05:28 AM   #18
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
>I have yet to have to cut off a hose, although I have done so when I was discarding the hose.<

Folks replacing hoses might consider extra length , so they can cut off an inch during service, and still replace the hose.
FF is offline   Reply With Quote
Old 12-24-2013, 06:25 AM   #19
TF Site Team
 
City: Ex-Brisbane, (Australia), now Bribie Island, Qld
Vessel Name: Now boatless - sold 6/2018
Vessel Model: Had a Clipper (CHB) 34
Join Date: Jun 2008
Posts: 10,101
Quote:
Originally Posted by FF View Post
>I have yet to have to cut off a hose, although I have done so when I was discarding the hose.<

Folks replacing hoses might consider extra length , so they can cut off an inch during service, and still replace the hose.
Yup, that's what I tend to do FF. I have tried the that heat gun thing - usually use that to get them on as well, but I always feel one damages them a bit doing that, so would rather cut and start with fresh end.
__________________
Pete
Peter B is offline   Reply With Quote
Old 12-24-2013, 07:04 AM   #20
Guru
 
jleonard's Avatar
 
Join Date: Jun 2008
Posts: 5,037
Quote:
Originally Posted by Bay Pelican View Post
Pete have you tried a heat gun and either a flat head screw driver or a channel lock pliers? I have yet to have to cut off a hose, although I have done so when I was discarding the hose.

Marty
There is a tool called a "hose pick" that will make it easy to remove a hose without damaging it. It really works well. I have used them for several years.
My son is an auto mechaninc and he uses them all the time. I was watching him once a few years a said I have to have one of those.
They come in various sizes.

Here's a set at Amazon.
http://www.amazon.com/GearWrench-KDT...ords=hose+pick

I think Craftsman sells a 4 piece set for not much money. If you use one once you will never use a screwdriver again.
__________________
Jay Leonard
Ex boats: 1983 40 Albin trunk cabin, 1978 Mainship 34 Model 1
New Port Richey, Fl
jleonard is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 12:28 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012