Reply
 
Thread Tools Search this Thread Display Modes
 
Old 08-05-2016, 02:42 PM   #1
Senior Member
 
grahamdouglass's Avatar
 
City: Vancouver Rowing Club, Coal Harbour, Vancouver, B.C.
Vessel Name: Summer Wind 1
Vessel Model: Marine Trader 41
Join Date: Nov 2012
Posts: 410
Seacock leaking

My brass Seacock for my raw water intake for my engine has developed a drip from the grease nipple. I started leaking when I squirted a little lithium grease into it this spring. Any comments out there about what to do?

I don't want to haul the vessel, and the leak is not that endangering and I can allways close the Seacock. But if there is a quick fix it would be nice.
grahamdouglass is offline   Reply With Quote
Old 08-05-2016, 02:50 PM   #2
Guru
 
rwidman's Avatar
 
City: North Charleston, SC
Join Date: Sep 2010
Posts: 4,869
I would hope your seacock is bronze not brass because brass does not hold up well in salt water.


The only suggestion I can offer other than replacing or repairing the seacock is removing the grease nipple and replacing it with a solid plug. For most of my life I thought grease nipples were threaded, but I found out a few years ago that some are a press fit with barbs to hold them in place. If yours won't unscrew, this have.


I suppose you could buy the end that snaps over the nipple when greasing it and snap it on and plug it.
rwidman is offline   Reply With Quote
Old 08-05-2016, 03:05 PM   #3
Senior Member
 
Join Date: Aug 2008
Posts: 264
Usually when a grease zert leaks it is because of a piece of contaminant that was injected, either in the grease or on the surface of the zert that is holding the ball/spring open. You can try working the valve while injecting some more grease. Always best to clean off the zert before injecting grease.
folivier is offline   Reply With Quote
Old 08-05-2016, 04:41 PM   #4
Guru
 
City: Here
Join Date: Sep 2012
Posts: 2,940
Quote:
Originally Posted by grahamdouglass View Post
I started leaking when I squirted a little lithium grease into it this spring. Any comments out there about what to do?
Have you seen a doctor ?
boatpoker is offline   Reply With Quote
Old 08-06-2016, 06:23 AM   #5
Guru
 
Shoalwaters's Avatar
 
City: Rodney Bay Lagoon
Vessel Name: "Dragon Lady"
Vessel Model: DeFever 41
Join Date: Feb 2008
Posts: 681
Grease fittings have a little ball inside which is held in the "closed" position by a spring. Disintegrated spring, corroded ball or dirt could allow seal to fail. Suggest replacing the grease fitting with one claimed to be resistant to corrosion.

Ball valves do not usually have grease fittings. Is it reasonable to assume that this is a tapered plug valve? If so, cycling several times (or better yet proper cleaning and servicing) followed by slight tightening might help.
__________________
Mike
If all else fails, read the instructions
If it ain't broke, don't fix it
Shoalwaters is offline   Reply With Quote
Old 08-06-2016, 07:30 AM   #6
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
Install a new grease fitting from an outboard motor source..
FF is offline   Reply With Quote
Old 08-06-2016, 09:20 AM   #7
Guru
 
City: gulf coast
Join Date: Jun 2014
Posts: 3,440
squirt some more grease and see if that clears it up.
bayview is offline   Reply With Quote
Old 08-07-2016, 08:06 AM   #8
Guru
 
Pgitug's Avatar
 
City: Punta Gorda, fl
Vessel Name: Escapade
Vessel Model: Nordic Tug 37 2002
Join Date: Jan 2015
Posts: 1,231
I would just replace the thru hull with a new one, while the boat is in the water.
We all need a little excitement in our lives to help break up our routine. This is such an opportunity.
Remember. No guts. No glory.

http://youtu.be/z97DChMRhM4
Pgitug is offline   Reply With Quote
Old 08-07-2016, 08:32 AM   #9
Guru
 
Pgitug's Avatar
 
City: Punta Gorda, fl
Vessel Name: Escapade
Vessel Model: Nordic Tug 37 2002
Join Date: Jan 2015
Posts: 1,231
Now if you only need to replace the valve you can do it the easy way.

http://youtu.be/f-P49Y-o6Y8
Pgitug is offline   Reply With Quote
Old 08-07-2016, 09:47 AM   #10
Guru
 
DHeckrotte's Avatar
 
City: Philadelphia, PA
Vessel Name: Revel
Vessel Model: 1984 Fu Hwa 39
Join Date: Nov 2015
Posts: 1,024
You can buy stainless steel zerks. McMaster-Carr.
DHeckrotte is offline   Reply With Quote
Old 08-07-2016, 10:05 AM   #11
Guru
 
HopCar's Avatar
 
City: Miami Florida
Vessel Name: Possum
Vessel Model: Ellis 28
Join Date: Aug 2011
Posts: 5,299
Like bayview said, try squirting some more grease through it to see if that cleans it. If you close the seacock first, the excess grease will just squirt into the opening in the ball or tapered plug.

If that doesn't fix it, just replace the zerk fitting. They're cheap.
__________________
Parks Masterson
Retired from Hopkins-Carter Marine Supply
HopCar is offline   Reply With Quote
Old 08-15-2016, 05:49 PM   #12
Senior Member
 
MartySchwartz's Avatar
 
City: Poulsbo, WA
Vessel Name: M/V Knot Knormal
Vessel Model: President 41
Join Date: May 2011
Posts: 282
Quote:
Originally Posted by Pgitug View Post
Now if you only need to replace the valve you can do it the easy way.

http://youtu.be/f-P49Y-o6Y8
Yea, right! Like ANYthing comes apart THAT easy on an old boat. I would not try that on my boat for anything short of a short term disaster repair to get be to the haul-out.

I would replace the zerk fitting with a stainless one or a bronze plug. There is no reason to replace a functioning hull valve just because a grease fitting is dripping.

Marty.........................
MartySchwartz is offline   Reply With Quote
Old 08-15-2016, 06:15 PM   #13
Guru
 
dhays's Avatar
 
City: Gig Harbor
Vessel Name: Kinship
Vessel Model: North Pacific 43
Join Date: May 2015
Posts: 9,046
Quote:
Originally Posted by MartySchwartz View Post
Yea, right! Like ANYthing comes apart THAT easy on an old boat. I would not try that on my boat for anything short of a short term disaster repair to get be to the haul-out.
Lol, that was my thought as well. Things never go that smoothly for me any time I work on the boat.
__________________
Regards,

Dave
SPOT page
dhays is offline   Reply With Quote
Old 08-15-2016, 06:58 PM   #14
Guru
 
cardude01's Avatar
 
City: Victoria TX
Vessel Name: Bijou
Vessel Model: 2008 Island Packet PY/SP
Join Date: Nov 2012
Posts: 5,290
Seacock leaking

I actually thought about doing this awhile back. Wanted to replace a faulty ball valve with a sea cock. Was going to use the seabung deal but wiser folks here on the forum talked me out if it. Glad I didn't try it. I hauled the boat, and the thru hull spun when I started to remove the valve so I had to replace and reseal the thru hull, and it took forever to get the nut off the thru hull. I'm sure I would have sunk the boat. 😂
cardude01 is offline   Reply With Quote
Old 08-15-2016, 08:18 PM   #15
Guru
 
psneeld's Avatar
 
City: Ft Pierce
Vessel Name: Sold
Vessel Model: Was an Albin/PSN 40
Join Date: Oct 2011
Posts: 28,119
Never trust a marine company that doesn't know the difference between a ball valve replacement and a seacock replacement.

Now if they did that with a Groco ball valve on the special flange and called it that...then we are talking big time and exactly why I went with that groco setup.
psneeld is offline   Reply With Quote
Old 08-19-2016, 09:03 AM   #16
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
"and it took forever to get the nut off the thru hull. I'm sure I would have sunk the boat."

$10 or $15 will get a nifty grinder to cut off the nut.
FF is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 11:04 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012