Wagner actuator - replace?

The friendliest place on the web for anyone who enjoys boating.
If you have answers, please help by responding to the unanswered posts.

Wagmore

Veteran Member
Joined
Sep 2, 2014
Messages
26
Location
N/A
Vessel Name
N/A
Vessel Make
N/A
This is one of those projects I'm trying to keep from getting away from me. Perhaps a picture tells the whole story...

31tUBFH.jpg


Hydraulic steering on a Nordic Tug 26 - Wagner 700 series helm pump and actuator pictured above. All is working fine now as-is - turns easily, no slop, no major leaks. Tiny drips in a couple places at the fittings, nothing coming out of the helm pump or actuator that I can see. However...that corrosion on the actuator seems significant to me, leaks or no.

I'm in the middle of an autopilot installation, a Simrad RPU-80 is about to go into the mix. I'm considering replacing all the lines. Not only because of the small leaks, but there are two compression unions splicing the lines that are there for unknown reasons.

7YBPy4e.jpg


Seems like a repair was made at one point, as the hydraulic lines aft of the unions are older than the ones up front. Maybe somebody didn't want to mess with the corroded connections at the actuator. Anyway, since I need to splice the line yet again to put in tees for the Simrad pump, resulting in four more compression fittings - this is starting to feel like a major hack, and last thing I want to deal with is failed steering. I need to do this right.

Is the actuator shown a concern if it's otherwise working fine? I'm a little gun shy about pulling those fittings, but if the actuator should be replaced anyway - I'll follow up with questions on how best to do that.
 
To me, it looks like someone used bronze/brass fittings screwed into a painted aluminum part. The corrosion can be cleaned up, remove all of the paint on the corroded part and replace the bronze/brass fittings with satinless, using a thread dope or teflon tape for fuel (not white) to insulate the threads enough that they won’t gall. Also, that heim joint has failed or the lever arm needs to be bushed (looks like both to me). Try just tightening the leaking fittings, that may solve the leak.

I also do not see any bonding on that rudder stock, you might investigate that more too?
 
Your bilge area/hardware actually look good to me! No seawater leaks at the shaft log & NO green corrosion... that's a rarity. Perhaps there was an autopilot pump installed close to the ram in the past & the unions are where it used to be plumbed into the steering? Or maybe the PO extended the steering lines rather than replace all of them due to the modification done back there?
If you wanted to mount your RPU80 in that area, just remove the unions & replace with tees to keep the fitting count down.
I'd think about adding the pump closer to the helm so you don't have to run a return line all of the way from the pump in the rudder area to the reservoir.
 
Spare Parts for the stearing cylinder

This is one of those projects I'm trying to keep from getting away from me. Perhaps a picture tells the whole story...

31tUBFH.jpg


Hydraulic steering on a Nordic Tug 26 - Wagner 700 series helm pump and actuator pictured above. All is working fine now as-is - turns easily, no slop, no major leaks. Tiny drips in a couple places at the fittings, nothing coming out of the helm pump or actuator that I can see. However...that corrosion on the actuator seems significant to me, leaks or no.

I'm in the middle of an autopilot installation, a Simrad RPU-80 is about to go into the mix. I'm considering replacing all the lines. Not only because of the small leaks, but there are two compression unions splicing the lines that are there for unknown reasons.

7YBPy4e.jpg


Seems like a repair was made at one point, as the hydraulic lines aft of the unions are older than the ones up front. Maybe somebody didn't want to mess with the corroded connections at the actuator. Anyway, since I need to splice the line yet again to put in tees for the Simrad pump, resulting in four more compression fittings - this is starting to feel like a major hack, and last thing I want to deal with is failed steering. I need to do this right.

Is the actuator shown a concern if it's otherwise working fine? I'm a little gun shy about pulling those fittings, but if the actuator should be replaced anyway - I'll follow up with questions on how best to do that.

Hi. I stumpled across your question, seaching for a seal-kit for a wagner 700 cylinder similar to yours. Whould you by any chance know where to buy such a kit. In advance thank you. Br Per
 
Read XsBanks comments about the fittings and how to deal with them. He means Stainless Steel ftgs, not satinless.
THe end caps are aluminum. Often the tow metals, brass/bronze and aluminum will not work well together.
It may not be required to toss the compression fittings. Instead find a Stainless Steel fitting that has the external male thread AND the internal female thread. Of course repaint the alum. cap. If the cylinder, actuator, is being wetted figure out how to stop
the wetting.

Check the rod end that connects to the rudder arm. They do wear especially if not greased. Those should be available as a replacement part.
 
Sometimes Hamilton Jet also has some used units and parts. My prior owner had over-tightened a fitting and cracked the cast aluminum part. Bought two used replacements at Hamilton Jet (plus a complete rebuild kit).
 
Back
Top Bottom