Reply
 
Thread Tools Search this Thread Display Modes
 
Old 11-25-2015, 04:16 PM   #1
Member
 
City: Jacksonville,Fl
Vessel Name: Wandering Star
Vessel Model: Chien Hwa Senator 43
Join Date: Aug 2015
Posts: 24
Holding tank sight tubes

Has anyone had luck installing sight tube on holding tank or do they just become unreadable? I was thinking (always dangerous) that if I installed with
petcock shut offs (to change out the clear tubing) from mid tank to top that this might work. Tired of finding out the tank is full the hard way. Tankwatch 3 sensors have given up. What do you think?
FredB is offline   Reply With Quote
Old 11-25-2015, 06:14 PM   #2
Guru
 
HiDHo's Avatar
 
City: Beverly Hills
Join Date: Feb 2012
Posts: 1,371
Sight glass is not the answer but if the tank is plastic and accessible try shining a high intensity light thru the side, you may be able to see the level. Tank level indicators fail because they get false readings off the residue that clings to the inside of the tank.
HiDHo is offline   Reply With Quote
Old 11-25-2015, 07:29 PM   #3
Scraping Paint
 
City: -
Join Date: Oct 2007
Posts: 13,745
We have changed the sight tubes on two of our four saddle tanks. The other two have fuel in them so we are waiting until we draw the tanks down to empty with transfers to the day tank before I change the tubes.

I did a lot of research on what type of tubing to use and in the end I went with the recommendation to use flexible PVC tubing. There is another type of tubing that works very well, too, and is more resistant to dye absorbtion but to use it I would have had to buy an expensive 50' roll which was far more than I need or would ever use. So I went with the PVC. It will absorb fuel dye a little faster than the other type but it's inexpensive and I can buy just the amount I need.
Marin is offline   Reply With Quote
Old 11-25-2015, 08:54 PM   #4
TF Site Team
 
Bacchus's Avatar
 
City: Seneca Lake NY
Vessel Name: Bacchus
Vessel Model: MS 34 HT Trawler
Join Date: Nov 2014
Posts: 7,826
Quote:
Originally Posted by FredB View Post
Tankwatch 3 sensors have given up. What do you think?
I've used and really like the Raritan non-contact level monitor - not inexpensive but it can handle multiple tanks if that's an advantage. Installation Manual

I installed it on 2 tanks (black & fresh water) and had zero issues in about 10 yrs
__________________
Don
2008 MS 34 HT Trawler
"Bacchus"
Bacchus is offline   Reply With Quote
Old 11-25-2015, 08:56 PM   #5
Guru
 
psneeld's Avatar
 
City: Ft Pierce
Vessel Name: Sold
Vessel Model: Was an Albin/PSN 40
Join Date: Oct 2011
Posts: 28,148
I would think that a sight tube of large enough diameter would work and be less susceptible to fouling.

Only experimentation would tell you how fast the sight tube may become cloudy enough before being useful.
psneeld is offline   Reply With Quote
Old 11-25-2015, 09:16 PM   #6
Senior Member
 
Join Date: Sep 2015
Posts: 204
A Harbor Freight digital temperature gun/sensor will detect the liquid level...seems to work best first thing in the morning as the air in the tank cools off more quickly than the liquid overnight.
go-planing is offline   Reply With Quote
Old 11-25-2015, 09:19 PM   #7
Guru
 
refugio's Avatar
 
City: Meydenbauer Bay Yacht Club
Vessel Name: Lulu (Refugio sold)
Join Date: Mar 2012
Posts: 1,284
Quote:
Originally Posted by Marin View Post
There is another type of tubing that works very well, too, and is more resistant to dye absorbtion but to use it I would have had to buy an expensive 50' roll...
I've always used rigid Tenite Butyrate Tubing, available in 6' lengths (I get mine at Laird Plastics in Seattle):
Excelon CAB (Clear Butyrate Tubing) combines optical clarity and scuff and impact resistance with ease of fabrication. It can be easily cut, bonded with cement and printed and is UL rated. Excelon CAB is ideally suited for plastic packaging and tubing, especially for scientific products. The exceptional permanence and dimensional stability of Excelon CAB make it ideal for thin-walled applications where superior toughness, rigidity and durability are required. Because of its low water absorption characteristics, Excelon CAB exhibits minimal dimensional change in environments of varying humidity. Can withstand Gamma and gas sterilization. Working temperature -40°F to 180°F.
I'm not quite sure how I'd deal with flexible tubing - maybe sleeve it with...rigid tubing?

I wouldn't do this with a holding tank though - the last thing I want when looking at that is "optical clarity"!
refugio is offline   Reply With Quote
Old 11-25-2015, 10:23 PM   #8
Guru
 
Capt.Bill11's Avatar
 
City: Sarasota/Ft. Lauderdale
Join Date: Apr 2014
Posts: 5,438
There is a very good reason you almost never see sight tubes in black water tanks.

Replace your TankWatch sensor.
Capt.Bill11 is offline   Reply With Quote
Old 11-25-2015, 10:49 PM   #9
Guru
 
City: Hotel, CA
Join Date: Sep 2011
Posts: 8,323
There are things in life you never wish to see again, the contents of the black water tank fall into that category.
__________________
Craig

It's easier to fool people than to convince them that they've been fooled - Mark Twain
CPseudonym is offline   Reply With Quote
Old 11-25-2015, 11:19 PM   #10
Guru
 
Xsbank's Avatar
 
City: Pender Harbour, BC
Vessel Name: Gwaii Haanas
Vessel Model: Custom Aluminum 52
Join Date: Sep 2013
Posts: 3,791
No kidding! Sight tubes? Install a bright light as suggested or perhaps just weigh your guests before and after?

Sight tubes!
__________________
Don't believe everything that you think.
Xsbank is offline   Reply With Quote
Old 11-26-2015, 05:11 AM   #11
FF
Guru
 
FF's Avatar
 
Join Date: Oct 2007
Posts: 22,553
Hart Systems - Home
FF is offline   Reply With Quote
Old 11-26-2015, 09:56 AM   #12
Senior Member
 
Sea Q's Avatar


 
City: Vancouver
Vessel Name: Sea Q
Vessel Model: Westport Mc Queen
Join Date: May 2015
Posts: 225
On big marine treatment systems I have installed only on the spill over tank after it has pasted thru the main aeration treatment tanks they use side mounted float level switch's "Big boys" as a back up they have sight glasses
The sight glasses had to be cleaned every week and the switch's every 2 months dirty but easy job
I would not use sight glasses on a raw waste tank they would plug and would be a bitch keeping clean .

On our personal boat we have 3 x 20 gallon holding tanks 5 heads
last year we installed air actuated ball valves on the tanks and replaced 2 of the heads from vacuum flush to Dometic grinder toilets.
Out of the three holding tanks the one collecting the waste from the living room kitchen dinning room main in the highest use so I need to put a sensor on it . It used to be a straight drop Sealand toilet into the tank now a grinder
So I'm on the search also for a sensor my primary tank

Since everything is ground up I'm expecting not to get build ups also I use a treatment that breaks up the waste to almost water. So the level should be the same across the tank .The tanks are fiberglass (but still viewable with a strong light)and thick so using outside proximity sensors will be a no go.
I will be ether going to a ultrasonic internal sensor or a simple floating ball on a cord "water float" both mounted top center of the tank as backup I will install a permanent light mounted on the outside clear section and flush so there is no bleed of light into the space.
Being cheap I will try the light first and the water float boating
Season is far away I have 4 months to get it done
Sea Q is offline   Reply With Quote
Old 11-26-2015, 10:41 AM   #13
Senior Member
 
Join Date: Sep 2015
Posts: 204
...Harbor Freight temperature gun....doesn't need cleaning...~$30.
go-planing is offline   Reply With Quote
Old 11-26-2015, 10:44 AM   #14
Guru
 
oscar's Avatar
 
City: Bethlehem, PA
Vessel Name: Lady Kay V
Vessel Model: 1978 Hatteras 53MY
Join Date: Oct 2015
Posts: 1,098
Quote:
Originally Posted by semi-planing View Post
A Harbor Freight digital temperature gun/sensor will detect the liquid level...seems to work best first thing in the morning as the air in the tank cools off more quickly than the liquid overnight.
I think you mean that after it all cools overnight, the air in the tank warms faster than the liquid?

Either way, I like the idea. I have one of those guns to keep an eye on trailer hubs/brakes/tires.
__________________
https://ladykay.blog/
oscar is offline   Reply With Quote
Old 11-26-2015, 01:09 PM   #15
TF Site Team
 
FlyWright's Avatar
 
City: California Delta
Vessel Name: FlyWright
Vessel Model: 1977 Marshall Californian 34 LRC
Join Date: Apr 2008
Posts: 13,728
Here's what I installed on my non-metallic fresh water and holding tanks for about $100 each. They have worked flawlessly.

Monitoring Systems

__________________
My boat is my ark. It's my mobile treehouse and my floating fishing cabin. It's my retreat and my respite. Everyday I thank God I have a boat! -Al FJB

@DeltaBridges - 25 Delta Bridges in 25 Days
FlyWright is offline   Reply With Quote
Old 11-26-2015, 08:04 PM   #16
Guru
 
HiDHo's Avatar
 
City: Beverly Hills
Join Date: Feb 2012
Posts: 1,371
we use one on our plastic holding tank, although with Purasan we seldom use it. Company has great customer service, our tank level indicator stripes didn't work, they shipped us replacements fast and that fixed the problem.
HiDHo is offline   Reply With Quote
Old 11-26-2015, 10:48 PM   #17
TF Site Team
 
Insequent's Avatar
 
City: Brisbane
Vessel Name: Insequent
Vessel Model: Ocean Alexander 50 Mk I
Join Date: Mar 2012
Posts: 4,262
Quote:
Originally Posted by FF View Post
Tank Tender tubes are fairly small, and the one in my black water tank did block up. But careful pumping of the TT air knob over a period of time has cleared it. My blackwater tank is shallow in depth so its not particularly accurate anyway.

But I do like the TT system, and I think installing the 10 tank instrument was one of the best things the PO did. I have 6 fuel tanks and 2 water tanks on it as well as the black water tank. I mainly use the TT for the water tanks as the fuel tanks all have sight tubes and are easy to glance at when in the ER.
__________________
Brian
Insequent is offline   Reply With Quote
Old 11-27-2015, 07:29 AM   #18
Moderator Emeritus
 
dwhatty's Avatar
 
City: Home Port: Buck's Harbor, Maine
Vessel Name: "Emily Anne"
Vessel Model: 2001 Island Gypsy 32 Europa (Hull #146)
Join Date: Sep 2008
Posts: 2,846
Quote:
Originally Posted by FlyWright View Post
Here's what I installed on my non-metallic fresh water and holding tanks for about $100 each. They have worked flawlessly.

Monitoring Systems

X2.
__________________
David Hawkins
Deer Isle, Maine
dwhatty is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Trawler Port Captains
Port Captains are TF volunteers who can serve as local guides or assist with local arrangements and information. Search below to locate Port Captains near your destination. To learn more about this program read here: TF Port Captain Program





All times are GMT -5. The time now is 11:51 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012