Go Back   Trawler Forum > Trawler Forum > General Discussion

Thread Tools Display Modes
Old 06-01-2012, 07:40 AM   #1
Keith's Avatar
Vessel Name: Anastasia III
Vessel Model: Krogen 42
Join Date: Oct 2007
Posts: 2,716
1st day of hurricane season

Everybody ready?

Keith is offline   Reply With Quote
Old 06-01-2012, 11:32 AM   #2
psneeld's Avatar
City: Avalon, NJ
Country: USA
Vessel Name: Freedom
Vessel Model: Albin 40
Join Date: Oct 2011
Posts: 12,762
Blo* me as the big wind says....

psneeld is offline   Reply With Quote
Old 06-01-2012, 12:22 PM   #3
healhustler's Avatar
City: Longboat Key, FL
Country: USA
Vessel Name: Bucky
Vessel Model: Krogen Manatee 36 North Sea
Join Date: Oct 2009
Posts: 3,843
Huh....we already had the un-named storm here that eventually became Beryl. It took an unusual attitude toward our small island and picked-up any organic material it could with it's 65 mph winds, slapping it on the side of our various en-sundry hulls. It took pressure washing or finger nails to pick off most of it. We're hoping that will be the worst of 2012.
healhustler is offline   Reply With Quote
Old 06-03-2012, 08:43 AM   #4
Senior Member
charles's Avatar
City: patterson
Country: usa
Vessel Model: CHB 45 Pilot House
Join Date: Mar 2012
Posts: 158
With the onset of Hurricane season, here is the STORM PREPARATION PLAN FOR CCRIDER
I post it so that those interested in minimizing damage to their boats will have an easy to use TEMPLATE for their own plan.
Pat, THE WIFE, actually executed this plan once when I was out of state and a storm was imminent.
It is specifically simple enough that a person unfamiliar with the boat can accomplish the task with minimum difficulty. The numbers that you see are for a DIAGRAM and pictures that are part of the plan and depict how the boat should look upon completion. KISS
Keep in mind that those who do not properly prepare their boats for a storm and then sustain damage, cause all of us to pay more for insurance.
Go forth and be prepared.

Use chafing gear on boat end of lines whenever possible. Pull the boat a foot or so further away from the dock, first removing the gang plank. When setting the lines have the same sag in the lines so that one does not tighten with no strain on its sister line (s).
Extra lines and chafing gear are located in the lazarette and in the boat storage closet on the dock. In the lazarette the lines are on the forward bulkhead. The chafing gear is just aft of the port rudder stock. This gear is short links of red hose and black hose. The split chafing gear is for the two anchor lines in the event the anchors are used. If C C Rider is at its home dock, the
lines to double and add are already attached to the pilings.
Double the bow lines onto each piling so that there are a total of four bow lines to the two bow cleats. #5 to #1 & #5 to #2.
1. Double the stern lines, #1 to #9 & #1 to #10.
2. Rig lines #2 to #3 & #3 to #7 on left side.
3. Rig lines #2 to #4 & #3 to #8 on right side.
Perform these numbered operations in order:
1. Canvas
Remove Privacy Curtain and stow it in the bridge console. (This takes time, as bolts and aluminum bars at the bottom must be removed. Leave in place if necessary)
Cockpit awning; Remove lacing and leave canvas loose as it can't be removed from the frame.
2. Dinghy: "Home Dock"
If boat is bow into the slip remove dinghy from the boat and store it on the ramp on the dock. Partially deflate it and cover it with the canvas. Use 2 of the 5/8" dock lines to secure the dinghy. The lines should be crisscrossed over the dinghy and tied to the dock. (see picture).
Make certain that the drain plug is removed.
Dinghy: "Away from Home"
If at all possible store the dinghy ashore and tie down.
If dinghy is to remain on the boat, lash it down as best you can.
3. Gin Pole
Fold it into its' crutch, it need not be lashed down.
4. Bimini
Loosen the 2 tie down straps and fold it forward.
Use the nylon braided lines that are located in the bridge console to wrap around the canvas of the bimini and cinch them tight.
Use one length of extra dock or other line and wrap the bimini with it so that the wind will not tear the canvas loose. Make certain each end of the canvas is tightly closed.
5. Antennas
VHF antenna (the long one on the port side) is released and leaned outboard and then rotated aft. It is then tied with a short piece of rope to the gin pole.
The shorter VHF antenna (on the port side) is laid forward. Tie or tape it to the broadcast band antenna on the port side of the pilothouse roof.
6. Mast
If the mast is folded simply tie a dock line to the rail on one side of the bridge and loop it around the mast immediately forward of the crutch and then tie to the opposite side rail. (see picture)
If the mast is standing, do the same as a. except position the rope on the rails slightly forward of the mast.
7. Cushions:
The cover for the cushions on the bridge may be stowed in the bridge console.
Remove the cushions and any other loose gear from the bridge and wipe off any dampness before stowing the gear in the pilothouse.
8. Bridge Dashboard:
Remove the depth sounder along with its cover, and the canvas cover over the instrument panel and compass. These may be stowed inside the console on the bridge.
Remove the Naugahide cover from the steering wheel.
9. Life Raft:
Remove the cover and put in the boat storage closet or inside the cabin.
1. Remove the canvas covers from the windshield.
2. Remove the sunscreens from the side windows.
3. Bring inside:
life rings
boat hooks (4)
barbeque pit
4. Make certain all ports, windows and doors are shut and locked tight.
5. Close the ventilator in the pilothouse.
1. Remove all loose gear from any counter top in the galley, including blender.
2. Remove all loose items from the sideboard in the salon.
3. Use lashings mounted on wall on chairs or lay them on cabin floor.

1. Make sure all loose gear is stowed
1. 110 volt circuit breaker panel inside the boat:
Everything off
2. Disconnect both shore power cords at the dock.The shore power cords and telephone cords may be left on the deck.
3. 12 volt panel:
All circuits OFF
4. 12 volt auxiliary panels
All circuits OFF.
5. Battery selector switch on 1
6. Propane
Turn OFF at the bottle.
7. Water
Disconnect the water hose from the dockside hose bib completely. Leave hose on deck.
In the event that the C C Rider is at a berth other than Patterson and the bow pilings are determined not be strong enough to
withstand the storm then the following procedure should be utilized:
Set the CQR and Danforth anchors at a 45 angle off of the bow. Use a boat to do this. Set at least 200' of rode. Place split hose chafing gear, from the lazarette, where the lines go over the bow roller. Winch both anchor lines tight.
Then use a short piece of line to tie the two anchor lines together JUST FORWARD OF THE ANCHOR ROLLER, then wrap this short line around the anchor lines and the anchor pulpit. This is to keep the anchor lines from being pulled off of the roller.
Subsequent to all of the foregoing being accomplished and checked, remove the gang plank and close the transom door.
Charles C Culotta, Jr
Patterson, La.
charles is offline   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

All times are GMT -5. The time now is 11:34 PM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2006 - 2012